antrax MultiBox-pro LAN+ Bedienungsanleitung Seite 42

ANTRAX Datentechnik GmbH / MultiBox-pro LAN+
port {port_num} watchdog port set {ip_port}
port {port_num} watchdog port show
port {port_num} watchdog pinginterval set {num}
port {port_num} watchdog pinginterval show
port {port_num} watchdog pingretries set {num}
port {port_num} watchdog pingretries show
port {port_num} watchdog retrybooting set {OFF=0|ON=1}
port {port_num} watchdog retrybooting show
port {port_num} watchdog bootretries set {num}
port {port_num} watchdog bootretries show
snmp
snmp port set {ip_port}
snmp port show
snmp snmpget enabled set {OFF=0|ON=1}
snmp snmpget enabled show
snmp snmpset enabled set {OFF=0|ON=1}
snmp snmpset enabled show
snmp snmpv2 enabled set {OFF=0|ON=1}
snmp snmpv2 enabled show
snmp snmpv2 public set "{text}"
snmp snmpv2 public show
snmp snmpv2 private set "{text}"
snmp snmpv2 private show
snmp snmpv3 enabled set {OFF=0|ON=1}
snmp snmpv3 enabled show
snmp snmpv3 username set "{text}"
snmp snmpv3 username show
snmp snmpv3 authalg set {NONE=0|MD5=1|SHA1=2|
SHA256=3|SHA384=4|SHA512=5}
snmp snmpv3 authalg show
snmp snmpv3 privalg set {NONE=0|DES=1|3DES=2|
AES128=3|AES192=4|AES256=5|AES192*=6|AES256*=7}
snmp snmpv3 privalg show
snmp snmpv3 authpasswd set "{passwd}"
snmp snmpv3 privpasswd set "{passwd}"
snmp snmpv3 authpasswd hash set "{passwd}"
snmp snmpv3 privpasswd hash set "{passwd}"
snmp trap type set {NONE=0|V1=1|V2=2|V3=3}
snmp trap type show
snmp trap receiver {trap_num} set "{dns_name}"
snmp trap receiver {trap_num} show
syslog
syslog enabled set {OFF=0|ON=1}
syslog enabled show
syslog server set "{dns_name}"
syslog server show
system
system restart
system fabsettings
system bootloader
system flushdns
vt100
vt100 echo set {OFF=0|ON=1}
vt100 echo show
vt100 numeric set {OFF=0|ON=1}
vt100 numeric show
vt100 reset
sets port watchdog TCP port
shows port watchdog TCP port
sets port watchdog ping interval
shows port watchdog ping interval
sets port watchdog ping retries
shows port watchdog ping retries
sets port watchdog retry booting to on/off
shows port watchdog retry booting state
sets port watchdog retry boot timeout
hows port watchdog retry boot timeout
enters cmd group "snmp"
sets SNMP UDP port
shows SNMP UDP port
enables SNMP GET cmds on/off
show if SNMP GET cmds are enabled
enables SNMP SET cmds on/off
show if SNMP SET cmds are enabled
enables SNMP v2 on/off
show if SNMP v2 is enabled
enables SNMP v3 on/off
show if SNMP v3 isenabled
sets SNMP v2 public cummnity
shows SNMP v2 public community
sets SNMP v2 private community
shows SNMP v2 private community
sets SNMP v3 username
shows SNMP v3 username
sets SNMP v3 authentication
show SNMP v3 authentication algorithm
sets SNMP v3 privacy algorithm
show SNMP v3 privacy algorithm
sets SNMP v3 authentication password
sets SNMP v3 privacy password
sets SNMP v3 authentication hashed password
sets SNMP v3 privacy hashed password
sets type of SNMP traps
show SNMP trap type
sets address and port of SNMP trap receiver {trap_num}
show address and port of SNMP trap receiver {trap_num}
enters cmd group "syslog"
enables syslog msgs on/off
show if syslog enabled
sets address of syslog server
shows address of syslog server
enters cmd group "system"
restarts device
restore fab settings and restart device
enters bootloader mode
flush DNS cache
enters cmd group "vt100"
sets console echo state
shows console echo state
sets numeric mode
shows numeric mode state
resets terminal
Seite 42