Werbung
Verfügbare Sprachen
Verfügbare Sprachen
User Manual
1. Charging Your Bluetooth ® Headset
1.1. Before you use the headset for the first
time, please charge the battery fully (approxi-
mately 2 hours are required).
1.2. The indicator light turns red while char-
ging, and will automatically turn blue after the
DRIVE & TALK
battery is fully charged.
Bluetooth Headset
1.3. When the headset is running out of bat-
tery, the indicator light will flash red.
Note: If left unused, a fully charged headset
will lose its power automatically. It is recom-
mended to charge the headset every three
months.
Do not place or keep the headset in extreme
conditions which may affect the headset's ope-
rations. The optimal temperature is between
15° C and 25° C.
Do not attempt to force open the built-in bat-
tery as this can damage the headset.
Multifunction Button
LED-Indicator
(MFB)
2. Turning on/off the headset
2.1. Turning on: Press MFB for some seconds
until the indicator light is flashing.
2.2. Turning on the Headset automatically: Put
the headset into the charging base, the
headset will beep and either the red indicator
light stays lit (if the battery is not charged
fully) or the blue light stays lit (if the battery is
fully charged).
2.3. Turning off the Headset: Press and hold
Earpiece
Ear Cap
the MFB for 5 seconds until the indicator light
switches off.
3. Pairing your headset with a Bluetooth
phone
3.1. Ensure that the headset is turned off.
Resetting-Key
3.2. Press and hold the MFB until the indicator
light flashes blue and red alternately.
3.3. Activate the Bluetooth feature on your
mobile phone.
3.4. Search Bluetooth devices (see the user
guide of your phone for instructions) and
select headset „Drive&Talk" from the found
devices list of the phone.
3.5.Enter the password „0000", confirm to
pair the headset with your phone. (If the pai-
ring cannot be completed successfully, please
repeat the above mentioned steps to try the
pairing again. Some phones pair without any
Rotated & Magnetic
password).
USB Charging Base
3.6. When the headset is off, it will connect
with the paired phone automatically if you
turn on the headset again.
4. Answering a call
When you receive an incoming call, you can
answer it in the following ways:
Method 1: Take the headset out of the char-
ging base.
Method 2: Shortly press the MFB.
10. Last number dialing
Method 3. Answer the call with your phone.
When the headset is connected to the pho-
ne(s), press the MFB twice. It will call the last
number automatically.
5. Ending a call
Note: If the headset is connected in multipoint
You can end the call by one of the following
mode, it will call the number from the phone
methods:
which was first paired or re-connected.
Method 1: Put the headset back into the
charging base.
11. Disconnecting
Method 2: Shortly press the MFB.
To disconnect the paired headset from
your phone, please turn off the headset or
Method 3: End the call with your phone.
disconnect the headset from the Bluetooth
menu of your phone.
6. Rejecting a call
12. Multi-point function
Press and hold the MFB for 2 seconds to reject
the call.
„Drive&Talk" Bluetooth headset allows you
to connect two 2 Bluetooth phones to the
headset at the same time.
7. Making a call – Manual dialing
When neither phone A nor phone B are pai-
Dial the number on your phone's keypad and
red, the multi-point operation is as follows:
press the call key.
12.1. Pair the headset with your phone accor-
ding to chapter 3. „Pairing your headset with a
8. Making a call – Voice dialing
Bluetooth phone".
Press the MFB once. Say the voice tag as
12.2. Turn off the headset and turn off the
soon as you hear the short beep. (Ensure
Bluetooth function on your phone. Turn the
your phone supports voice dialing function,
headset on again.
and you have recorded the voice tag in your
12.3. Repeat the steps from chapter 3. „Pai-
phone. See the user guide of your phone for
ring your headset with a Bluetooth phone"
instructions.)
with your phone B.
If the multi-point operation is already activa-
9. Two-call handling
ted, there are two means to use it:
A) When one phone is connected and you
Option 1: Activate the Bluetooth function of
are having a call and receive another inco-
phone A, look for „Drive&Talk" and choose
ming call
„Connect". Both headsets are connected with
the headset now.
9.1. Shortly press the MFB to hold the active
call and answer the incoming call.
Option 2: Activate the Bluetooth function of
phone A and phone B. Turn on the headset,
9.2. Shortly press the MFB to switch between
it will automatically re-connect with both
the call. One call will be on hold.
phones within one minute.
9.3. Press the MFB for 1 second to you can
end the current call and answer the waiting
13. Automatic re-connection
call.
If you turn the headset on and it is already
B) The headset is connected with two
paired with one phone, it will connect auto-
phones, you are having a call from phone
matically with your phone.
A. There is an incoming call from phone B,
you can answer both call by following these
If it happens that the automatic re-connection
steps
does not work, please connect it manually.
9.4. Shortly press the MFB to answer the call
from phone B. From this moment, the call
14. Reset
from phone A is on hold.
If the headset does not respond even if the
9.5. Re-press the MFB. You can switch bet-
battery is full, please press the MFB with a
ween these 2 calls.
slender object, for example a toothpick. After
the reset and the restart the headset can be
9.6. Press and hold the MFB about 1 second to
used as usual.
end the current call, you will be transferred to
the other phone to answer the call.
15. The Headset Charging Notice
Note: Before using two call handling, please
make sure that your phone supports „Hands-
When the headset is charging, the indicator
free Profile". Please also make sure that „to
light is red, while it is blue when the charging
put call on hold" service is available in your
is completed. If the indicator light does not
network.
react, please check the following:
Please ensure that the USB output is 5V.
16. Usage of necklace
16.1. Put the ear speaker into the hole of
pendant.
16.2. You will hear a 'Click'.
16.3. If you need to take out the headset,
please pull the headset from the gap (down-
ward) again.
17. Safety and general information
17.1. Please read this guidebook carefully.
17.2. Use only supplied and approved charger
or another MLINE charger.
17.3. Please keep the headset away from hu-
midity, liquid, fire, sharp objects and extreme
temperature.
17.4. Protect the headset against dust and
dirt.
17.5. Do not clean the headset with abrasive
detergents.
Bluetooth Specification V 3.0
Transmission Power
Class 2
Operation Range
Up to 10 Meters
Frequency Range
2.402-2.480 GHz
Battery
Built-in Rechargeable 3.7V/
50mAH Li-polymer Battery
Charging Voltage
DC 4.75-5.25 V
Charging Time
About 2 hours
Talk Time*
About 4 hours
Standby Time *
up to 100 hours
Dimensions (mm)
53.5 x 13.5 x 6
Weight
About 6.6 g
*The time mentioned as above may vary due to user's
operation mode and device settings.
CE Certification
This product is CE marked according
to the provision of the R&TTE Directi-
ve (99/5/EC).
We declare that this product is in
compliance with the essential require-
ments and other relevant provisions of
Directive 1999/5/EC.
For further information and the
complete declaration of conformity
respectively, please go to www.mline.
com/download
Bluetooth® is a trademark owned by
the Bluetooth SIG, Inc.
For any further information, please
feel free to visit www.mline.com
Correct disposal of this product
(Waste Electrical & Electronic Equip-
ment)
(Applicable in the European Union and
other European countries with separa-
te collection systems)
This marking shown on the product or
its literature, indicates that it should
not be disposed with other household
wastes at the end of its working life.
To prevent possible harm to the
environment or human health from
uncontrolled waste disposal, please
separate this from other types of
wastes and recycle it responsibly to
promote the sustainable reuse of
material resources.
Household users should contact either
the retailer where they purchased this
product or their local government of-
fice, for details of where and how they
can take this item for environmentally
safe recycling.
Business users should contact their
supplier and check the terms and
conditions of the purchase contract.
This product should not be mixed with
other commercial wastes for disposal.
IMPORTANT NOTE
To comply with RF exposure require-
ments, this device may not be co-loca-
ted with any other transmitter or
antenna.
Werbung
