Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Field of application:
The devices are only suitable for distributing radio and television signals inside
the house! If a device is used for other purposes, no warranty is given!
Scope of delivery:
1 × Single cable multiswitch II (SCR)
1 × Operation instructions
Outputs and user bands:
There are 4 user bands (acc. EN 50494) available at each of the 4 subscriber
ports:
UB1: 1331 MHz
UB2: 1382 MHz
UB3: 1433 MHz
UB4: 1484 MHz
Connectors, switches, mounting angles:
1
SAT inputs for LNB
LV, LH, HV and HH for Quattro LNB
LV and LH for 1st Wideband LNB
HV and HH for 2nd Wideband LNB
2
TERR input
9
3
Equipotential bonding connection
4
Subscriber ports
5
DC connector for power
4
supply SZU 99-06
10
6
SAT cascade outputs
7
TERR cascade output
8
Mounting angles
9
Wideband-Quattro switch
10 Legacy/CSS switches
Equipotential bonding and mounting:
To avoid dangerous power surges (e.g. risk of fire and danger of life) the device
must be connected to the equipotential bonding according to EN 60728-11.
Use the equipotential bonding connection at the device (3).
To connect the outer conductor of the coaxial cable to the equipotential
bonding, use e.g. QEW earthing angles at the inputs and outputs of the
device.
Use appropriate mounting screws for the mounting angles of the device (8).
Legacy mode:
Each output can be switched to legacy mode separately (10). The output
then behaves as a normal multiswitch output. This allows to connect
receivers which don´t support CSS/SCR.
Legacy mode can not be used with wideband LNBs!
Quattro LNB:
1
2
5
3
RF installation:
8
Connect the SAT inputs (1) of the multiswitch to the LNBs of your SAT
6
7
reception antenna. Connect the output signals of a terrestrial amplifier or a
CATV amplifier to the terrestrial input (2).
Connect the subscriber outputs (4) of the multiswitch to the antenna
sockets. Use highly shielded coaxial cables with F connectors. Suitable
cables and connectors can be found in the current AXING catalogue or
under www.axing.com.
If you don´t use cascade units to expand the multiswitch, terminate
the outputs (6 + 7) on the lower side with termination resistors
CFA 11-00 (not included in delivery).
Wideband-LNB:
The single-cable multiswitches can be used with wideband LNB with an
oscillator frequency of 10.4 GHz.
Slide the sliding switch (9) to W = Wideband.
Connect the first wideband LNB to the connectors LV and LH and the
second wideband LNB to the connectors HV and HH.
Power supply:
The single cable multiswitch is fed by the connected receivers.
The LNBs are fed via the SAT IF lines.
If a Quattro LNB is used, it can usually be supplied by the connected
receivers. If wideband LNBs are used, then the have to be supplied
e. g.:
9 via a head amplifier
9 as pictured above, via an ext. power supply SZU 99-06 (not included)
Cascading:
CSS/SCR
Up to three single cable multiswitches can be connected to one cascade.
Legacy
Connect the outputs of the single cable multiswitch with the inputs of
CSS/SCR
the next single cable multiswitch units.
Legacy
Use F/F Quickfix adapters CFA 4-01 (not included in delivery).
Terminate the outputs of the last single cable multiswitch with resistors
CFA 11-00 (not included in delivery).
Werbung
