Werbung
Verfügbare Sprachen
Verfügbare Sprachen
HI-Q TOOLS MOUNTING STAND III
Ord. Nr. 60150700070
CONTENT
1 mounting stand
2 rubbered swing arms
2 racing adapters (V-forme)
The HI-Q TOOLS mounting stand III simplifi es a lot of reparation and mounting work on your
two-wheeler. Modern motorcycles often have a high empty weight of several hundred kilogramms.
Therefore please use the HI-Q TOOLS mounting stand III always with the greatest care in accordance to
these operating instructions and the manufacturer's specifi cations to avoid damage on your two-whee-
ler and injuries on involved persons. The HI-Q TOOLS mounting stand III with the delivered swing arm
supports is only appropriate for jacking up motorcycles with rear swing arm with straight box profi le.
Never use the HI-Q TOOLS mounting stand III for other purposes.
ASSEMBLY
The HI-Q TOOLS mounting stand III is ready as soon as the supports (pointing inwards) are put into
the open bars of the lift and fi xed with the screws (on each side) possible widths: with rubbered angle
22-31cm, with racing adapter 21-34 cm. The self-locking nuts of the safety srews are tightenend gently
without tightening the profi le of the stand. If the swingarm has a thread support, we recommend to use
the optionally available racing adapter with castors (view abbove).
If there is a swing arm with straight box profi le with thread supports, use the rubbered swing arm sup-
ports (included in the delivery). The HI-Q TOOLS mounting stand III is not appropriate for triangle swing
arms or hooked „banana swing arms" without thread supports or one arm swing arms.
USE
Before using the HI-Q TOOLS mounting stand III check if your motorcycle generally fulfi ls the conditions
to be lifted by the HI-Q TOOLS mounting stand III.
The max. load capacity is 150 kg – therefore the total weight of the two-wheeler incl accessories
may not exceed 300 kg. The rear swing arm has to be appropriate for the lift (no construction forms
as described above). If the rear swing arm shall be demounted, the axle has to be loosened before
jacking up the motorcycle. The same is valid for other tightened boltings on the two-wheeler. Never jack
up the motorcycle alone – let yourself help by a second strong person, keeping the motorcycle on the
handlebar in vertical position. Lifting the two-wheelers if it is standing inclined on the side stand, can
damage the HI-Q TOOLS mounting stand III and may cause that the vehicle slips off.
60150700070-Bedienungsanleitung.indd 5-6
USE WITH RUBBERED SWING ARM SUPPORTS
DIRECTLY ON THE SWING ARM
Mount the rubbered swing arm supports and adjust the width of the HI-Q TOOLS mounting stand III on
your two-wheeler. Put the supports from the back on the swing arm bars of the motorcycle and move
the supports so they are completely under both bars. The swing arm bars have to be put onto the
swing arm supports in full width to make sure the motorcycle is carried safely. Generally the swing
arm bars do not have to be positioned strongly angled on the vehicle.
Axle, pieces of the wheel adjustment, shock absorber mountings and other protruding construction
pieces do not have to be put on the swing arm supports to avoid damage on the HI-Q TOOLS mounting
stand III or your vehicle. Put the HI-Q TOOLS mounting stand III with the supports on the rear third of
the swing arm bars, so they rest safely on full width. Before lifting the motorcycle make sure again,
that the HI-Q TOOLS mounting stand III is safely assembled and the helping person keeps the vehicle
safely in position. Then press the motorcycle lift on the connection tube strongly but slowly under the
vehicle until it lies on the lift.
USE WITH RACING ADAPTERS DIRECTLY ON THE
SWING ARM
Assemble the racing adapters and adjust the width of the HI-Q TOOL mounting stand III on your
two-wheeler. Put the supports from the back on the premounted adapters of the swing arm and move
the racing adapters so they are coating the adapters from the bottom completely. The swing arm
adapters have to lie entirely on the racing adapters to make sure the motorcycle is supported safely.
Axes, wheel adjustment pieces, shock absorber supports and other protruding construction pieces may
not lie on the racing supports to avoid damage on the HI-Q TOOLS mounting stand III or on your
vehicle. Before lifting the motorcycle make sure again that the HI-Q TOOLS mounting stand III is safely
assembled and the helping person keeps the vehicle safely in position. Then press the mounting stand
on the connection tube strongly but slowly and consistently under the vehicle until it rests on the stand.
Thus we can guarantee the correct mounting and use of the product.
POLO Motorrad und Sportswear GmbH
41363 Jüchen – www.polo-motorrad.de
State: 03/2017
GB
13.03.17 17:06
Werbung
