Installing And Connecting - Naim Audio UnitiQute 2 Kurzanleitung

UnitiQute 2 • English
1.
1.1 Stand your UnitiQute 2 on an appropriate, stable surface. Make sure it is well ventilated.
1.2 Check that the mains voltage specified on the UnitiQute 2 rear panel is appropriate for your country. Connect to the mains
using the supplied cable but do not switch on until all other connections have been made.
1.3 Identify the rear panel Signal Ground Switch and select the chassis option unless your UnitiQute 2 is connected in a hi-fi
system incorporating another earthed source component (all Naim CD players, for example), or mains hum is audible through
the speakers when it is switched on.
1.4 Connect the speakers to the UnitiQute 2 speaker sockets. Ensure that the positive and negative orientation at both ends of the
cable is the same for both channels. Your Naim retailer will be able to supply appropriate speaker cables if required.
1.5 In order to use the DAB/FM tuner a suitable aerial must be connected to the DAB/FM aerial socket.
1.6 If a subwoofer or external power amplifier is to be used, connect its signal cable to the UnitiQute 2 preamp output socket.
Your Naim retailer will be able to supply an appropriate cable if required.
1.7 To play audio from internet radio stations, UPnP™ servers, Spotify
must be connected to the internet via a network router. Either connect the UnitiQute 2 network socket to your network router
using an Ethernet cable, or connect the supplied Wi-Fi antenna to the rear panel Wi-Fi aerial socket.
1.8 For UnitiQute 2 to play audio from Bluetooth
panel Bluetooth aerial socket.
1.9 If your UnitiQute 2 is to play audio files stored on a USB storage device, such as an iOS device or a memory stick, connect it,
using an appropriate cable if necessary, to the front panel USB socket.
1.10 If any external audio sources are to be used with your UnitiQute 2, connect them using the appropriate cables to one or more
of the rear panel analogue or digital inputs.
2. Switching On and Getting Started
2.1 Once all connections have been made, switch on your UnitiQute 2 using its rear panel on/off switch. The UnitiQute 2 will
display a welcome screen and select its Analogue input or, if it has been previously used, the last input selected.
2.2 For initial setup purposes your UnitiQute 2 is best controlled from its remote handset. Use the navigation (56) keys to select
inputs or menu items and the ok/list key to confirm selections. To return to a previous menu use the left (3) key.
2.3 The UnitiQute 2 interface language can be changed. Enter Setup Mode and select Language.

Installing and Connecting

®
Connect, or other Naim streamer units the UnitiQute 2
®
streaming devices, the supplied Bluetooth antenna must be attached to the rear
Note: Full UnitiQute 2 installation and operational information can be
found in the Reference Manual available at: www.naimaudio.com
Note 1.7 & 1.8: UnitiQute 2 is supplied with both Wi-Fi and Bluetooth
aerials. Each aerial must be fitted to the correct rear panel aerial socket.
The Bluetooth aerial is the shorter one of the two.
Note 1.9: Most UMS (Universal Mass Storage) USB devices are compatible
with the UnitiQute 2 USB audio input. Such devices might include portable
digital music players, smart-phones, tablet computers, USB memory sticks
and memory card readers. Non UMS USB devices such as older MP3
players may be connected to the UnitiQute 2 front panel input using a
3.5mm stereo jack cable from their headphone sockets.
Note 2.1: If your UnitiQute 2 is left unused it will switch to displaying the
time after two minutes. This delay time can be adjusted via the setup
menus. If the clock is not set it will display "No Time".
Note 2.3: Enter Setup Mode by pressing
Setup 1/10
the handset setup (
4Language
menus by using the navigation (563) keys.
Inputs
Select options by pressing the
Analogue Outputs
ok/list key. Leave Setup Mode by pressing
Headphones
the setup or exit key.
) key. Navigate setup