Herunterladen Inhalt Inhalt Diese Seite drucken

Indesit IDE 44 Installationsanleitung Seite 24

Vorschau ausblenden Andere Handbücher für IDE 44:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 36
Installation
Positioning the Appliance
Position the appliance in the desired location. The back
should rest against the wall behind it, and the sides, along
the adjacent cabinets or wall. The dishwasher is equipped
with water supply and drain hoses that can be positioned
to the right or the left to facilitate proper installation.
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screwing
them in or out) to adjust the height of the dishwasher,
making it level. In any case, the appliance should not be
inclined more than 2°.
If the appliance is level, it will help ensure proper perfor-
mance.
This dishwasher model can be built under a single worktop
(please read the relevant instruction sheet).
Cold water connection.
Connect the cold water supply hose to a 3/4 gas threaded
connection, taking care to screw it tightly onto the tap. If the
water hoses are new or have been out of use for an extended
period of time, let the water run to make sure it is clear and
free of impurities before making the connection. If this
precaution is not taken, the water inlet could get blocked,
causing damage to your dishwasher.
Hot Water Connection
The water supply to the appliance can also be connected to
the house's hot water line (centralised system, heating
system), as long as it does not exceed a temperature of 60°
C.
In this case, the wash cycle time will be shortened by about
15 minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following
the same procedures as those for the connection to the cold
water line.
Anti-flooding protection
Your dishwasher is provided with a special system which
blocks the water supply in the event of leaks inside the
appliance. It is further equipped with a water inlet hose that
can withstand extremely high pressures and that turns bright
red in the event of breakage. Safety in the event of flooding
is ensured by the second clear hose that contains the former
and thus highlights the latter when it has turned bright red. It
is vital that you check it on a regular basis: if you see it has
turned bright red, then you know you have to replace it as
soon as possible. Call for an authorised technical engineer to
come and replace it.
GB
Drain Hose Connection
Fit the drain pipe into a drain
line with a minimum diameter
of 4 cm or place it over the
sink. Avoid restricting or
bending it. Use the special
plastic elbow provided (see fi-
gure) to position it in the best
possible way. The part of the
pipe marked with the letter A
should be between 40 and 100
cm above the ground.
The pipe should not be immersed in water.
Attention: The special plastic hose support must be solidly
fastened to the wall to prevent the drain hose from moving
and allowing water to spill outside the drain.
Electrical Connection
After making sure that the voltage and frequency values for
the current in the home correspond to those on the rating
plate (located on the stainless steel inner door of the
appliance) and that the electrical system is sized for the
maximum voltage on the rating plate, insert the plug into
an electrical socket which is earthed properly (the earthing
of the appliance is a safety requirement mandated by law).
If the electrical socket to which the appliance must be
connected is not appropriate for the plug, replace the plug,
rather than using adpators or the like as they could cause
overheating and burns.
Should the electricity supply cable be damaged, we
recommend that you only contact authorised Technical
Service Centres for the replacement.
22
A

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Ide 45

Inhaltsverzeichnis