Installation - Kicker KXA800.5 Benutzerhandbuch

MODEL:
IMPORTANT SAFETY WARNING
PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER IN
A DISTORTED, CLIPPED OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO SYSTEM
TO OVERHEAT, POSSIBLY CATCHING FIRE AND RESULTING IN SERIOUS DAMAGE TO YOUR
COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO 4 INCHES (10CM) OPEN
VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1 INCH (2.5CM)
CLEARANCE BETWEEN THE FRONT OF THE SPEAKER AND ANY SURFACE.
PERFORMANCE
Model:
RMS Power, AMP1 and AMP2
@ 14.4V, 4Ω stereo, ≤ 1% THD+N
@ 14.4V, 2Ω stereo, ≤ 1% THD+N
@ 14.4V, 4Ω mono, ≤ 1% THD+N
RMS Power, SUB channel
@ 14.4V, 2Ω mono, ≤ 1.5 % THD+N
@ 14.4V, 4Ω mono, ≤ 1.5 % THD+N
Length [in, cm]
Height [in, cm]
Width [in, cm]
Frequency Response [Hz]
Signal-to-Noise Ratio [dB]
Input Sensitivity
Selectable Electronic Crossover
KickEQ™
Subsonic Filter
NOTE: 2017 KX amplifi er subwoofer channels are 1Ω stable - power rating equivalent to 2Ω operation, +/- 10%

INSTALLATION

Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no
items behind the area where the screws will be driven. Choose a location that allows at least 4" (10cm)
of open ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger
compartment. Drill four holes using a 7/64" (3mm) bit and use the supplied #8 screws to mount the
amplifi er.
Wiring: Disconnect the vehicle's battery to avoid an electrical short. Then, connect the ground wire to the
amplifi er. Make the ground wire short, 24" (60cm) or less, and connect it to a paint-and-corrosion-free,
solid, metal area of the vehicle's chassis. Adding an additional ground wire of this same gauge (or larger)
between the battery's negative post and the vehicle chassis is recommended.
2
2017 KXA 5ch Amps Rev H.indd 2 2017 KXA 5ch Amps Rev H.indd 2
KX.5-SERIES AMPLIFIERS
OWNER'S MANUAL
KXA800.5
KXA800.5
50W x 4
100W x 4
200W x 2
400W x 1
200W x 1
12-3/4, 32.4
2-1/8, 5.5
8-5/16, 21
AMPS 1-2: 10Hz–20kHz
SUB: 10Hz–160Hz
>95dB, A-weighted, re: rated power
250mV–10V
AMP 1: OFF/HP/LP, variable 10–5,000Hz with 10X switch;
24dB/octave
AMP 2: OFF/HP/LP/BP, variable HP 10–500Hz,
variable LP 40–5,000Hz with 10X switch; 24dB/octave
SUB: Variable LP 10–160Hz; 24dB/octave
Boost - Variable 0-18db; Center Frequency - 40Hz
Variable 10–80Hz; 24dB/Octave
4/25/2017 1:08:46 PM 4/25/2017 1:08:46 PM