Weekly Maintenance; Rear Squeegee Rubber Replacement; Squeegee Hose Cleaning; Squeegee "V" Type (Optional) - Jade 55c Bedienung Und Wartung

GB

WEEKLY MAINTENANCE

REAR SQUEEGEE RUBBER REPLACEMENT

Check the squeegee rubber wear and eventually turn
or replace it.
For the replacement it is necessary to:
1. Lift the squeegee acting upon the lever (12).
2. Release the hook (1) of the rubber holder blade
and take the rubber off.
3. Turn the rubber to a new side or replace it.
To reassemble the squeegee repeat reverse the op-
erations above mentioned, inserting the rubber on
the guides (2) and blocking it with the rubber holder
blade.

SQUEEGEE HOSE CLEANING

Weekly or in case of insufficient suction, it is neces-
sary to check that the squeegee hose is not ob-
structed. Eventually, to clean it, proceed as follows:
1. Take off the hose from the squeegee coupling (1)
and release the guide spring of the squeegee hose (2).
2. Wash the inside of the hose with a water jet,
from the squeegee hose side.
3. To reassemble the hose repeat reverse the opera-
tions above-mentioned.

SQUEEGEE "V" TYPE (OPTIONAL)

Alternatively to the standard squeegee, a "V"-shaped
squeegee is available, especially indicated for floors
with large joints.
This squeegee is interchangeable with the standard
one, same assembly on the machine, same adjust-
ment in height, pressure and inclination.
Different though are the methods in assembly and
disassembly of the squeegee rubbers.
SQUEEGEE "V" TYPE (OPTIONAL): REAR RUBBER
REPLACEMENT
Check the squeegee rubber wear and eventually turn
or replace it.
For the replacement it is necessary to:
1. Lift the squeegee acting upon the lever (12).
2. Unscrew the tie rods (1) on the terminals (2) of
the rubber holder blade and disengage the terminals.
3. Unscrew the wing nuts (3) and take off the rub-
ber holder blade (4).
4. Turn the rubber (5) to a new side or replace it.
To reassemble the squeegee repeat reverse the oper-
ations above mentioned, inserting first the rubber (5)
into its guides, then positioning the rubber holder
blade and finally screwing down all wing nuts and
the tie rods of the two terminals.

CLEANING OF SOLUTION TANK AND FILTER

1. Bring the machine to an appropriate place for
tanks draining.
2. Unscrew the solution tank cap (1).
3. Unscrew the exhaust plug (2).
4. Rinse with a water jet the solution tank.
5. Rinse the solution tank filter placed inside the
exhaust plug (2).
6. Reassemble all parts.
ATTENTION:
This operation must be carried out using gloves to
protect from contact with dangerous solutions.

TWO-MONTHLY MAINTENANCE

FRONT SQUEEGEE RUBBER REPLACEMENT

Check the wear of the squeegee rubber and eventu-
ally replace it.
For the replacement it is necessary to:
23
1. Take off the squeegee hose (3).
2. Disassemble the squeegee from the support ro-
tating the levers (2) counterclockwise by sliding the
stud bolts (1) in their slots.
3. Unscrew the wing nuts (4) in the front part of
the squeegee.
4. Take off the rubber holder blade.
5. Replace the front rubber.
6. Reassemble all parts.
SQUEEGEE "V" TYPE (OPTIONAL): FRONT RUBBER
REPLACEMENT
Check the squeegee rubber wear and eventually turn
or replace it.
For the replacement it is necessary to:
1. Disassemble the squeegee from the support as
indicated under "SQUEEGEE CLEANING".
2. Unscrew the tie rods (1) on the terminals (2) of
the rubber holder blade and disengage the terminals.
3. Unscrew all wing nuts (6) and take off the rubber
holder blade (7).
4. Take off the rubber (8) and replace it.
To reassemble the squeegee repeat reverse the oper-
ations above mentioned, inserting first the rubber (8)
into its guides, then positioning the rubber holder
blade and finally screwing down all wing nuts and
the tie rods of the two terminals.

SIX-MONTHLY MAINTENANCE

CHECK OF THE BRAKE

Check the braking efficacy and that both pads (1)
which act upon the traction wheels, in resting posi-
tion, have got a distance of not more than 3mm
from the wheels. If necessary, adjust them through
the fixing nuts (2).
GB