Soldron OCD2-1999 Handbuch Seite 7

4. Advanced settings and read-out
☞ Press both UP ( ) and DOWN ( ) buttons together for 3 seconds. INFO is displayed.
✚
Press UP( ) button until you reach the desired sub menu. Select the sub menu with the OK (
Monitoring of energy consumption
☞
The thermostat calculates average time it has been switched on allowing you to monitor your energy consumption.
In the thermostat you can read out:. Total switch-on time in percentage in the latest 2 days, 30 days or 365 days.
Calculation of operational costs per day: (switch-on time:100) x kW x kWh-price x 24 h per day
Example: Read-out: 30 % in the latest 365 days
2 days
30 days
365 days
Software version
☞
Regulation sensor
Limit sensor
(visible if configurated as OCD2)
4-event sequence
The present event sequence flashes: Days 1-5, followed by days 6-7. To change, press the UP (
☞
and then day 7 flashing, or all 7 days are flashing. Select the required sequence with the OK (
☞
Selection of type
Type OCD2-1999 has a built-in temperature sensor and an externally temperature sensor. In this configuration the thermostat controls
☞
the temperature within the room and use the externally temperature sensor as limit sensor
Type OCD2 can be changed into type OCC2-1991 with an external temperature sensor that normally is placed in the floor construction.
In this configuration the thermostat controls the temperature of the floor and not the temperature within the room. OCD2 can also be
changed into type OCC2-1999 with a built-in temperature sensor. In this configuration the thermostat controls the temperature of the
room, and the external temperature sensor should not be installed.
☞
☞
☞
☞
Max and min allowed temperature range. The temperature setting range of +5˚ to +40˚C can be limited to prevent a too high or too
☞
low temperature being selected under manual or comfort mode. For OCD2 with limit sensor the max. and min. temperature range refer
to the temperature of the limit sensor. For example: A wood floor covering should not be allowed to exceed a maximum of 27˚C. Low
limitation is used where the temperature of the floor is required never to fall below the minimum set temperature.
☞
☞
☞ ☞
Time and temperature scale selection
☞
☞
☞
Size of heating system: 1,2 kW (ask the installer)
Cost of power: 0,2 EUR / kWh
Calculation: (30:100) x 1,2 kW x 0,2 EUR / kWh x 24 h = 1,7 EUR per day
}
}
☞
☞
}
Press UP (
readouts.
No changes can be made here. Use the OK ( ) button to
end.
5-2: 4 events in 5 days +
}
2 events in 2 days.
6-1: 4 events in 6 days +
2 events in 1 day
7-0: 4 events in 7 days
OCD2-1999 With 2 sensors;
built-in room sensor and
incl. floor sensor 3m
OCC2-1991 Incl. floor sensor 3m
OCC2-1999 With built-in room sensor
Maximum allowed temperature setting. Use the UP (
DOWN ( ) button to increase or reduce, and OK (
accept.
Next is displayed LoLi. Press OK ( ) button to continue.
Minimum allowed temperature setting. Use the UP ( ) or
DOWN ( ) button to increase or reduce and OK ( ) button to
accept.
You can select either ˚C or ˚F scale, and 12 or 24 hour clock as
follows:
Press UP ( ) or DOWN ( ) button to change settings. Confirm
the required scale with the OK button ( ) button.
) button.
) or DOWN ( ) button to show the different
) button until you have days 1-6
) button.
) or
) button to
7