Gemini CD-240 Bedienungsanleitung Seite 3

of the art professional CD player is backed by a three year warranty,
that you carefully read all the instructions.
CAUTIONS
D not use this CD Player at temperatures below 41" F/5" C or higher than
O
Do not place the unit in an unstable location.
When disconnecting the power cord from an AC outlet, always grasp it by
To prevent electric shock, do not remove the cover or the bottom screws.
There are no user serviceable Parts inside. Please refer servicing to a
qualified technician.
Do not use chemical solvents to clean the unit.
Keep the laser pickup clean by keeping the drawer closed.
Keep this manual in a Safe place for future reference.
SAFETY CERTIFICATIONS
Laser Diode Properties
Material: Ga - Al - As
Wavelength: 755 - 815 nm (25" C)
Laser Output: Continuous Wave, max. 0.5mW
IMPORTANT NOTE
make the drawings easier to understand, we will only number the right side
(20) switch and the
ROBO START (l), POWER
SLIDE (22)
LINE VOLTAGE SELECTION
Model CD-240 is a dual voltage unit. lt will operate at 115 or 230 volts. The
unit is preset at the factory to 115 volts. To set the proper voltage follow
1. Place the head of a screw drtver in the center of the VOLTAGE SELEC-
(22) switch found on the rear Panel.
TOR SLIDE
Slide the switch left for 115 volts or push the switch right for 230 volts.
3. Do not forte or twist the switch. Excessive forte may cause darnage. If
CONNECTIONS
1. Using the induded cable,
plug
2. Plug one end of a set of RCA connectors into each of the
(25)
3. Plug the other end of the RCA connectors into any available line level
input jacks on your mixer. If you are playing the CD-240 through a
FUNCTION DESCRIPTIONS
ANTI-SHOCK BUFfER MEMORY: With 20 SECONDS OF ANTISHOCK
BUFFER MEMORY, each side of the CD player stores 10 seconds of
future play to ensure that any harsh movement or bumping of the unit will
not interrupt play and play will continue smoothly.
POWER
(22) switch, found on the rear Panel, is properly set, plug the unit in and
VOLTAGE SELECTOR
one end into the
LINE OUTPUT
press the POWER (20) switch. The unit will turn on. Pushing the
(20) switch a second time will turn the unit off.
POWER
The DISC TRAY (19) is where the CD is held during loading,
DISC TRAX
unloading and playback. Pressing the disc tray OPENICLOSE BUTTON
and 8 cm CDs. Please note, if the CD-240 is in the play mode, the tray
will not open.
remove a CD from the
The
DISPLAY: DISPLAY
auto tue, continue (for continuous play), and 3 different time displays.
These time displays are time elapsed on the track, time remaining on the
disc and üme remaining on the track. Time is measured in minutes,
seconds and frames.
PLAYBACK DISPLAY:
remaining to play and flashes slowly when the track has 15 seconds left.
The
PLAYBACK DISPLAY
the Operation to change from play to pause or from pause back to play.
TRACK SKIP H H
Use the SEARCH JOG WHEEL
mode. Use the SEARCH JOG WHEEL (9)
Use
and Speed. Tuming the dial in the dockwise direction will scan forward
and counter dockwise will scan
increases as the dial is tumed further.
n
STOP
available choices listed under
after the tue Point has been memorized, pressing the CUE BUTTON
(15) will cause the CD player to enter the pause mode (playlpause LED
blinks green) at the memorized tue point (the tue LED glows yellow). If
the track. Holding down the tue button changes the tue function to
(allowing you to hear the music play at whatever tempo you
PREVIEW
adjusted to by holding the tue button down). Releasing the tue button
retums you to the preset tue point.
button in the play mode. (the tue LED BLINKS yellow), repeats the
button was pressed (there will be a slight delay between the end and the
restart of play). Press the CUEIB (10) button again or pause play to EXIT
the repeating play.
Press
beginning of the previously saved CUUB from normal play.
SINGLE-AUTO CUEICONTINUOUS:
(21) and
(3) button activates the AUTO CUE FUNCTION. The
CONTINUOUS
AUTO CUE FUNCTION Causes the unit to pause at the beginning of
of every track). Pressing the
button a second time activates the CONTINUOUS function causing the
unit to play continuously (after the last track, the unit will retum to the
first track of the disc and continue to play). Pressing the SINGLE-AUTO
OUS function.
ROBO START: Press
(the button will illuminate). Use ROBO START in SINGLE-AUTO
START
CUE MODE to altemate play between the two sides of the CD player
(one track from one side, then one track from the other side). See the
' Robo Start Instructions" section for further instructions.
assign the percent the pitch wntrol slide will have. The 4% button will
assign +/-4% to the pitch wntrol slide. The 8% button will
Page 2
DISC TRAY (19)
Press the
DISC TRAY (19).
(5) Shows the track number, pitch value, single-
The (6) displays the time
PLAYBACK DISPLAY
(6) flashes quickly when the track has 5
TRACK SKIP BUTTONS (12)
The
SEARCH JOG WHEEL (9)
(9) to make fine adjustments in PAUSE
to bend the pitch for precise
(8) to select the scanning direction
the SEARCH DIAL
reverse. The scanning Speed
In
(2) switches the üme display between the three
button to retum to the
Pressing the
SINGLE-AUTO CUEI
SINGLE-AUTO CUEICONTINUOUS (3)
(3) button a third time deactivates the CONTINU-
the (1) button to activate
ROBO START
Use
holds both 12 cm
let you select
has two functions.
to the beginning of
(10)
BUTTONS (13) to