Electrical Connection - Whirlpool AKZ 205/AV Installationsanleitung

10200153aGB.fm Page 4 Monday, September 5, 2005 3:27 PM
• If the worktop is made of wood, use the spring
clips and screws provided.
1. Secure the spring clips (D) (fig. 7) with the
screws provided (E) (fig. 7) as shown, paying
attention to the specified distances.
2. Fit the cooktop into the worktop.
• If the worktop is made of marble, plastic,
ceramics, stone, etc., the cooktop must be
secured with special brackets (F) (fig. 8), Code
4819 404 78697, available from After Sales Service.
1. Fit the cooktop into the worktop.
2. Place the 4 brackets (F) in position in
accordance with the thickness of the worktop
as shown in fig. 8.
3. Fasten the 4 screws (G) in the positions (H)
(fig. 8).

Electrical connection

• Regulations require that the appliance be
earthed.
• Connection to the mains must be carried out by a
qualified electrician in accordance with the
manufacturer's instructions and in compliance
with local regulations.
• The installer is responsible for connecting
appliances correctly to the mains and for
observing the safety regulations.
• The oven power cable must be long enough to
connect the built-in appliance to the mains.
• Observance of safety directives requires that a
multi pole switch with a minimum contact gap of
3 mm be used for the installation.
• Do not use multiple plug adapters or extension
leads.
• After the oven has been installed, the electrical
components must be inaccessible.
Connecting the oven to the power supply
• Make sure that the voltage indicated on the rating
plate is the same as the mains voltage. The rating
plate is on the front edge of the oven (visible
when the door is open).
• Remove the two fastening screws of the terminal
box cover (if supplied) located on the bottom
part of the oven's rear covering. Remove the
cover to gain access to the terminal box and
insert the power cable (see table) through the
opening located on the bottom of the oven.
Connect the cable to the terminal box and secure
it to the cable fastener. Put the cover back on by
inserting the two blades in the slots and fasten it
with the two screws.
4
Power supply cables table
N° of conductors Type of cable
~
H05 RR-F 3 X 4 mm²
1N+
~
H05 RR-F 3 X 4 mm²
2 +
~
H05 RR-F 4 X 2.5 mm²
2N+
~
H05 RR-F 5 X 1.5 mm²
3N+
~
H05 RR-F 4 X 2.5 mm²
3 +
Interconnecting cooktop and oven
Important: do not connect the oven to the
power supply before you have finished
connecting the oven and cooktop.
• Before connecting the oven to the power supply,
make sure that the cooktop is among the ones
listed in the cooktop/oven pairing product sheet
provided.
• Connect the two male 3 pole (H) (fig. 9) and
4 pole (J) (fig. 9) connectors of the cooktop to the
respective female connectors located on the
right hand side of the top covering of the oven.
• Unscrew the nut of the ground screw (K) (fig. 9)
on the left hand side of the top covering of
the oven and insert the yellow/green earth cable,
leaving the washer in place.
• Screw the nut back onto the screw and tighten it
as far as it will go.
Securing the oven
• Lift the oven getting hold of it by the openings on
the sides and insert it into the housing unit, being
careful not to trap the power supply cable (fig. 10).
• Center the oven in the housing unit before
securing it.
• Make sure that the plastic spacers (if provided)
are positioned correctly in the fastening holes.
Then anchor the oven to the housing unit with
the screws provided.