Joyetech eVic VTC Dual Bedienungsanleitung

Notice for Use:
Thank you for choosing Joyetech!
Please read this manual carefully before use to ensure that your usage is correct
information or have any questions about the product or its use, please consu t your Ioca Joyetech agent, or
visit our website at nww.joyetech.com
Product Introduction:
evic VT C Dual features the replaceable back cover for
alternatively using one or two cells as you prefer where
maximum output can be reached to 75W and 150W
respectively. evic VTC Dual combines unique and
attractive styling with a super large OLED screen,
supporting RTC/VW/VT/Bypass/TCR modes. It also
comes with upgradeable firmware and dual battery
protection system In addition, there are various
attractive colors for you to choose.
evic VTCDualI
between Stealth on and Stea th off function In Stealth on Mode, you can still vape with the screen off. To
quick y see your settings in stealth on mode, you can tap the fire button to display
5. Key lock function: When the device is on, simultaneously press the two regulatory buttons. This wil
switch between Adjustment Lock and Adjustment Unlock function. While Key Lock is on, the regulatory
button WII not work to prevent accidental adjustments
6. Switch the display mode: Press the two regulatory buttons simultaneously in power off state,
the display WII rotate 180 degrees
7.Set screen protection time: When the device is on, simultaneously hold the fire button and
the right regulatory button (on the bottom) to enter into adjustment interface
regulatory button again to enter into screen protection time setting Choose the protection time
and press the fire button to confirm.
8. How to set the time: Press the fire button 3 times to enter into the setting menu. The first row
will flash to Press the left regulatory button to switch between Hour, Minute, Year, Month and Day
Press the right regulatory button to adjust the parameter. (Note: only Year can be reversed by
pressing the eft regulatory button when adjusting). Also the evic AIO has two ways of time
displaying: Dial Display and Numerica Display for your preference.
3 eVicVTCDuaII English
Press the fire button to confirm
How to set the TCR?
n power-off condition, press the fire button and the right regulator simultaneously for about 5
seconds to enter into the TCR set menu:
1 Press right/left regulator to choose between TCR MI, M2 or M3;
2 Then press the fire button to select certain parameter;
3 Press the regulator to set the parameter;
4 Long press the fire button or leave it for about 10 seconds to confirm
Here's the TCR Value Range for
your reference as follows:
Note: 1. The TCR value in the above form is 105
multiplied Of its actual value
2 The TCR value range is 1-1000
Temperature settings
Under TEMP mode (including TCR), coil temperature can be adjusted (from 100-3150C, 200-6000F) with the
regulatory button Press right regulatory button to increase the temperature while left regulatory button to
Down it. A momentary press Of the regulatory button will increase/decrease
5 eVicVTCDuall English
2. New coil, same coil
When replacing the atomizer, whose resistance is larger than the previous one to some degree, resetting of
the atomizer "base resistance" may be required —this is the resistance of the atomizer coil when it is used at
room temperature
When the tank is detached, press the power button to initiate a reset. After fitting a new atomizer head and
reinstall the tank, "New Coil, Same Coil" message with the ohm reading will appear on the display
right regulatory button to confirm that a new coil has been fitted.
Should you see this message for any other reason
from recent use press the left regulatory button so that the 'base resistance" is not reset Always do remember
to choose correct operation mode to suit the coil that fitted to ensure that temperature control is accurate
3. Wattage adjustment under VT mode:
Maximum initial wattage can be adjusted under VT mode. Press the fire button 3 times to enter the menu
Press the left regulatory button, and the second row wil blink. Press the right regulatory button to increase
the wattage After that, press the fire button to confirm
Note: (1) VT mode only supports a maximum of 1.5 ohm. The device will automatically switch to VW mode
when the resistance is larger than 1 5 ohm
(2) When Kantha' Wire is applied in VT mode, the device will also automatically switch to VW mode after
working for 2 seconds.
evic VTCDuall rnolish
7
Temperature Protection:
In VT mode, if the actual temperature Of coil is higher than the set temperature, the device
shows: "Protection"
Temperature Alert:
If the temperature of device is over 70 C , the output will shut off automatically and the screen wil
display "Device Too Hot"
Special for dual batteries
Imbalanced Batteries:
If the voltage difference between the two cells reaches to 0.3V or higher,
will appear on the screen when plugged the cable
Charge Error:
If the device detects no charging current while plugged into the charger, the screen wi
"Charge Error
Check Battery:
When the device is powered on and plugged into the charger, if the cells are not put inside or
accidentally placed opposite, the screen will show "Check Battery"
evic VTCDuall
9
1 This warranty provides repair free of charge for defective Joyetech brand merchandise. Warranty period is
90 days from date of purchase by the end user
2 This warranty may be void as a result of any of the fol owing conditions:
* Customer does not provide warranty card and original receipt of purchase
• Merchandise failure or damage is caused due to improper use or unauthorized repair.
* Merchandise failure or damage as a result of excessive force such as dropping
* Merchandise failure or damage as a result of usage outside of recommended operating conditions (see
precautions in usage manual)
* Merchandise failure or damage caused by improper use of water or other liquid (see usage manual for
operating instructions)
• Merchandise failure or damage due to usage with non-Joyetech components (charger, battery, and power cable)
3 This warranty does not cover personal items or consumable goods and attachments, including but not
limited to: mouthpiece, cartridge, atomizer head, lanyard, and leather sheath
4 This warranty does not cover any nor-mjoyetech brand products This warranty is only valid for eligible
Joyetech brand products during the warranty period of 90 days after date of purchase as indicated on proof
of purchase
evic VTCDualI EngilSh
11
If you require any additional
510 Thread and
Spring connector
—e
Fire Button
OLED Screen
Alternative Back Cover
Regulatory Button
Micro LISB Port
Press the right
Material TCR Value Range
Nickel 600-700
NiFe 300-400
Titanium 300-400
ss (303, 304, 316, 317) 80-200
the temperature by increments Of
especially when reinstalling the same coil that is stil warm
mbalanced Batteries"
show
How to use:
1. Power on/off: Hold the back cover and slide to take it off Put the 18650 battery into the back cover and
push it back into the body Press the fire button 5 times in quick succession to turn the device on and Off
Repeat the same operation to change the back cover which holds two cells_Repeat the same operation to
change the back cover which holds two cells.
Note: (1)When using with single battery, maximum output and voltage wil be 75W and 9V While with two
batteries, it can be reached to 150W and 9V respectively
(2) Please be careful not to use battery with torn shell for safety
2. Vaping: Hold the fire button and inhale through the mouthpiece
Please adjust the wattage to a proper range according to your atomizer before use.)
3. Charging & Upgrading
Please use high-rate 18650 cells with continuous rated discharge current >25A
(Use married batteries for dual back cover). We kindly suggest you take out the cells
and charge them with a stand alone charger. The micro USB port is on the top of the
eft side. Connect it with a micro USB cable to charge or upgrade your device.
4. Stealth functio
When the device is on, simultaneously hold the fire button and the left regulatory button. This will switch
General functions
Switch among different modes
Press the fire button 3 times to enter into the setting menu Press the right regulatory button to switch among
TEMP, TCR, POWER and BYPASS
(1) Under TEMP or TCR mode, while flashing, press the left regulatory button to enter into its subsidiary menu
to set: VT, PWR, COIL and AMP When adjusting VT, press the right regulatory button to switch among Temp
Ni, Temp Ti and Temp SS316/ MI , M2 and M3 modes. Press the fire button to confirm. When the AMP row is
flashing, press the right button to switch among AMP, PUFF and TIME
(2) Under POWER Or BYPASS mode, while flashing, press the left regulatory button to enter into its subsidiary
menu When AMP row is flashing, press the right regulatory button to switch among AMP, PUFF and TIME.
PWR ISO
Temp-SS316
COIL0.50 Q
The Temp-SS316 mode is especially designed for stainless steel 316 coil. We kindly recommend
you Joyetech BF-SS316 atomizer head
14:07
TCR (MI, M2, M3)
With the TCR (Temperature Coefficient of Resistance) function available now, you can customize
2016-04-13
your temperature control coils (Ni, T i, SS) on your own. Under TCR mode, when the mode
PWR ISO
indication is still flashing, press the eft regulatory button and the sub-menu items (MI , M2, M3)
0.50 Q
will flash. Press the right regulatory button when it still flashing to switch among MI, M2 and M3
50C (IOOF). Long press the regulatory button will rapidly increase/decrease
TCR Set,
Logo Mode
Press the fire button and the right regulatory button simultaneously to enter into the setting menu.
Continue to press the right regulatory button for two times, and you will enter into the Logo Mode
M2 0120
Simply choose on/off by pressing the right regulatory button Press the fire button to confirm
M3 0120
Supplementary functions
1. Lock/unlock the atomizer
Press the fire button three times to enter into the menu. Then press the eft regulatory button 2 times, and the
second row where the resistance display will blink. Press the right regulatory button to lock or unlock the coil
resistance When the Ock sign displayed, thus the resistance is ocked
Note: (1) Please lock the resistance only when the coil is used at room temperature
"base resistance" of the atomizer. Temperature
changed. Once the resistance is locked, you can remove the tank while the coils are hot or cold and it wil
function under the same parameter
(2) Please unlock the resistance before you change to a different atomizer or temperature control wil not
work correctly. When the resistance is un ocked, please ensure any new coil is installed at room temperature
when first used to retain temperature accuracy
Malfunction indication and protection
Over 10 Second Protection:
and the OLED Screen will display "Over IOS protection"
Atomizer Short-circuit Protection:
Press the When atomizer short-circuit occurs, the OLED Screen will display 'Atomizer Short"
Weak Battery Alert: In VT/VW mode, when the device installed with an atomizer is working and
the voltage of battery is below 2 9V, the device shows: Weak Battery Meanwhile, the output
power will be reduced accordingly.
Low Power Alert: When the vo tage of battery is below 3 3V, the device shows: Battery Low
If you continue to press the fire button, the device shows: Battery low ock, and cannot work
Please recharge the battery to reactivate.
Unlocking Battery Low:
As soon as charging has commenced low-voltage protection wil be unlocked
Atomizer Low Alert: When
ower than 0.050hm in VT mode, the OLED screen will display "Atomizer LOW'
TEMPTI
Check USB Adapter:
P rotect tn
If the voltage Of the USB Adapter is 5 8V or higher, the screen will appear "Check USB Adapter" when
plugged into the charger or pressing the fire button
0.40 Q
Cautions:
00.0 A
1 Only have your evic VTC Dual repaired by Joyetech
as it may lead to further damage to the item and/or personal injury
2 evic VTC Dual should be operated in dry conditions between temperatures of -IOC (14
and charged between OC (32 F ) to 45 C (113 F
3. evic VTC Dual is designed with authentic Joyetech components
I mbalanced
aatter les unauthorized components may cause the device to function improperly and/or lead to damage
Warranty
Please consult your Joyetech product warranty card We are not responsible for any damages caused by
human error. Our warranty is not available for products purchased from third party vendors
Joyetech agrees to provide repair under warranty pursuant
ttery
Joyetech reserves the right of final decision
the content of this warranty
Warning
1 Keep out of reach of children
2. This product is NOT recommended for use by young people or non-smokers
3. This product is NOT suitable for use by child, pregnant or breast-feeding women, people who're
allergic/sensitive to nicotine
Release the fire button and exhale (Note:
modes Press the fire button to confirm
resistance under VT mode:
control will remain accurate, as long as the coil is not
When the power button is pressed for over 10 seconds, the output will shut off
the resistance of atomizer is lower than 0.1 ohm
Do NOT attempt to repair it on your own
Applying evic VT C Dual with
to the following
in all warranty cases. Joyetech
terms.
TEMPNI
4500 450T
ISO PWR 75.0
0.20 COIL 0.20 Q
AMP00.0 AMP00.0 g
(single battery) (dual batteries)
eVic VTCDuaI 2
TCR MI
7S.o
0.40 Q
00.0 g
Enqhsh eVic VTCDual 4
the temperature setting
LOGO
This WII lock the correct
eVicVTCDual 6
pow ER
45.0w
4.5S
COIL O.SOQ
AMP 09.54
VVeak
Battery
Atomizer
in VW mode or
eVicVTCDual 8
) to 60C (140 T)
terms and conditions:
anqlish eVic VTCDual
10
may interpret and revise
eVic VTCDual
12