Operating Elements - Grundig Fine Arts M 100-T Servicehandbuch

M 100-T

OPERATING ELEMENTS

5
POWER TUNING
by by
POWER POWER
Front of the tuner
POWER This button is used for switching the tuner on and off.
TUNING Q R You use these buttons to start the station search (AUTO TUNING) or to
advance the frequency step by step (MANUAL TUNING). If you keep the
button depressed, station search is accelerated.
STATION 1 2 These buttons are used to scroll through the station memory in ascending (>) or
descending (<) order.
MEMORY This button stores the actual station at the lowest empty memory location.
When pressing this button longer, the AUTO STORE function will be started.
CANCEL This button is used to delete individual memory locations or, if desired, the
entire memory contents (by keeping the button depressed for more than 10 seconds).
BAND This button is used to switch to the FM ANTENNA, FM CABLE and MW bands.
IF/MONO
Pressing this button repeatedly switches the FM reception mode to STEREO WIDE
STEREO NARROW
MUTING
MUTING
MUTING STEREO
MUTING STEREO
MONO
MONO
GRUNDIG Service
6
STATION TUNING
1 2
2
TUNING TUNING 1 1 STATION STATION 2 TUNING TUNING
MUTING MONO STEREO AUTO ANTENNA CABLE
########
MHz
MONO WIDE MONO NARROW
OPERATION
Selecting the wave band
• Select the desired wave band (FM ANTENNA,
FM CABLE or MW) by pressing BAND.
ANTENNA
• Pressing this button switches to the next wave
band in the following order: FM ANTENNA- FM
MHz
CABLE - MW - FM ANTENNA
CABLE
– The display shows the selected band.
MHz
If you receive broadcasts via broad band cable
of a public or private cable service, there may
be high signal inputs at your antenna terminal,
kHz
which may in turn cause reception disturbances.
• If this is the case, select FM CABLE to switch on
the input attenuator. This reduces the antenna
input sensitivity, thus reducing disturbances. This
setting is automatically stored after 5 seconds.
FM reception
WIDE/NARROW, STEREO/MONO
The FM reception mode is automatically set to stereo
and wide every time automatic tuning is started.
Still, there are stations with disturbances or noise
in the audio signal, due to weak signal or inter-
ference of adjacent (neighbour) stations.
The IF/MONO button provides a step-by-step pro-
gressive attenuation of those disturbances or noise.
• When the FM reception is disturbed, press
ANTENNA
IF/MONO. The reception mode switches to
MHz
'STEREO NARROW'
ANTENNA
interference from strong neighbour stations.
• If stereo narrow reception still exhibits too much
MHz
disturbing noise press IF/MONO again to
ANTENNA
select 'MONO WIDE'. Now the mono function
MHz will reduce noise due to weak reception.
ANTENNA
• It is unlikely that you still hear noise but a last
step is to select 'MONO NARROW' by pressing
MHz
IF/MONO again. You have now selected the
highest noise disturbance reduction both for neigh-
bour station interference and for weak reception
DISPLAY
1 2
MUTING MONO STEREO AUTO
M100-T
M100-T
MEMORY MEMORY 9
MEMORY
1 MUTING – This indicates that the MUTING
CANCEL CANCEL
CANCEL
function is active.
BAND
BAND
BAND
2 MONO – This comes on if the MONO function
is activated.
IF/MONO IF/MONO
IF/MONO
3 STEREO – This indicates that the tuner is
receiving FM stereo broadcasts
4 AUTO – This indicates that the AUTO TUNING
function is active
5 Signal strength – The more dashes you can see,
the stronger the reception of the station you have
tuned to.
6
(NARROW/WIDE) and the triangle
lights up if the unit is exactly tuned to a station.
7 ANTENNA – comes on when the antenna
attenuator is switched off (FM ANTENNA).
8 CABLE – comes on during broadband cable
reception if the antenna attenuator is switched on
(FM CABLE).
9 Station number seven-segment display – This
shows the number of the selected memory
location (1 to 59)
STEREO WIDE etc.
0 14-segment display – for (RDS) station name,
frequency, radiotext, RDS time, selected
programme type or messages.
LANGUAGE SELECTION
Language selection
You can call up the programme type display in
the following languages: english, german,
french, portuguese, spanish, italian, dutch, and
swedish.
• Keep the IF/MONO button pressed while the
unit is turned off, and then turn on the tuner.
– The current language appears in the display.
• By using the STATION 1 2 buttons you can
call up the desired language.
• Store your selection by pressing the MEMORY
button.
thus avoiding
Allgemeiner Teil / General Section
3 4 5 6 7 8
ANTENNACABLE
kHz
MHz
0
– Shows the chosen FM IF bandwidth
1 - 9