Ca-Mi EOLO Benutzerhandbuch Seite 11

The EOLO aerosol is intended for use in the electromagnetic environment specified below.
The customers or the user of the EOLO aerosol should assure that it's used in such an environment.
Emissions Test
Irradiated / Conducted emissions
CISPR11
Irradiated / Conducted emissions
CISPR11
Harmonic emissions
IEC/EN 61000-3-2
Voltage fluctuations / flicker emissions
IEC/EN 61000-3-3
The EOLO aerosol is intended for use in the electromagnetic environment specified below.
The customers or the user of the EOLO aerosol should assure that it's used in such an environment.
Immunity Test
Electrostatic discharge (ESD)
IEC/EN 61000-4-2
Electrical fast transient / burst
IEC/EN 61000-4-4
Surge
IEC/EN 61000-4-5
Loss of voltage, brief voltage
interruptions and variations
IEC/EN 61000-4-11
Magnetic field
IEC/EN 61000-4-8
Conducted Immunity
IEC/EN 61000-4-6
Irradiated Conducted
IEC/EN 61000-4-3
Note U is the value of the power supply voltage
T
Use a soft dry cloth with not – abrasive and not – solvent detergets.
MAKE SURE THAT INTERNAL PARTS OF THE APPLIANCE DON'T COME INTO CONTACT WITH LIQUIDS AND THE PLUG IS
Procced as follows to disinfect the accessories:
1. Turn the upper part of the nebulizer in an anti-clockwise direction;
2. Disconnect the internal pisper at the base of the nebulizer using the fingers;
3. Use denatured alcohol or a hypochlorite - based solution, easily found at chemist, to clean the accessories;
4. After using the appliance, disassemble the nebulizer and clean all parts in warm water, rinse carefully and remove excess water using a soft
cloth and leave to dry in a clean place.
After each treatment clean thoroughly each component of the nebulizer (except air tube) removing medication residual and possible impurities.
Clean all parts in warm water.
Rinse thoroughly making sure that all deposits are washed away and let dry.
Guidance and manufacturer's declaration – Electromagnetic Emissions
Compliance
Group 1
Class [B]
Class [A]
Complies
Guidance and manufacturer's declaration – Electromagnetic Emissions
Compliance
± 6kV on contact
± 8kV in air
± 2kV power supply
± 1kV differential mode
5%U for 0.5 cycle
T
40%U for 05 cycle
T
70%U for 25 cycle
T
<5%U for 5 sec
T
3A/m
3Vrms 150kHz to 80MHz
(for appliances that aren't
life - supporting)
3V/m 80MHz to 2.5 GHz
(for appliances that aren't
life - equipment)
CLEANING DEVICE
CELANING THE ACCESSORIES
DO NOT BOIL OR PUT IN AUTOCLAVE THE ACCESSORIES
Electromagnetic environment - guidance
The EOLO aerosol only used RF energy only for its internal functioning.
Therefore its RF emissions are very low and are not cause interference in
proximity of any Electronic appliances.
The EOLO aerosol can be used in all environments, including domestic and
those connected directly to the public mains distribution that supplies power
to environments used for domestic scopes.
Electromagnetic environments - guidance
Floors should be wood, conceret or ceramic tile. If floors are covered
with synthetic material, the relative humidity should be at least 30%.
Mains power quality should be that of a typical commercial
environment or hospital
Mains power quality should be that of a typical commercial
environment or hospital
Mains power quality should be that of a typical commercial
environment or hospital If the user of the EOLO aerosol request that
the appliance operates continuously, the use of a continuity unit is
recommended.
The power frequency magnetic field should be measured in the
intended installation location to assure that it's sufficiently low.
NOT INSERTED
11
-
-