VISA VE-R37T Installations- Und Betriebs-Anleitung Seite 4

7. For each location, insert a lag bolt and washer into the wall.
8. Tighten bolt with an open ended socket wrench by turning clockwise until tight.
CAUTION: Do not over-tighten bolts-doing so may cause unnecessary damage to the
wall. Avoid excessive torque.
CAUTION: Do not release the wall plate until it is properly mounted and secured to the
wall.
Concrete/Brick Installation
NOTE: The concrete anchors must be used for concrete installation. They can be
purchased at your local hardware store.
1. Begin by placing the wall plate into position against the wall, using the bubble level to
keep it level.
2. Mark off six holes to be used for securing the mount and place the wall plate aside.
3. Next, drill holes using an electric drill and 10mm masonry bit.
4. Insert a concrete anchor into each hole.
5. If necessary, a hammer can be used to lightly tap each anchor into place so that they
are flush with the wall.
6. Once all of the anchors are in place, move the wall plate back into position.
7. Attach the nut onto the threaded shaft that is protruding from the wall.
8. Do not tighten until all nuts are in place.
TV Plate Assembling
After you install the wall plate on your wall, you need assemble the TV plate to the wall
plate
1. Pull out the connecting plates forwards
2. Attach the TV plate to the front piece of the connecting plates, making sure inner four
holes 75x75mm fitting to the four holes on the front plate.
3. Then connect the TV plate with the front
piece by inserting 4pcs M8X15 Allen Screws
into M8 washers, TV plate, front piece of the
connecting plates and finally tightened with
M8 nuts.
4. Make sure all four pieces screws has been
tightened before you go for next step.
Display Bracket Installation
1. To ensure optimal installation,
includes various screws of different diameters an
2. Place your TV screen down on a soft, fl
points that are located on the back of the display.
3. Determine which screw is the correct length by carefully inserting a straw, or
toothpick, and mark how deep the mounting point is.
4. If your display has a curved back or a recessed
thread mounting point, a spacer must be used.
NOTE: Select the spacer that is closest in depth to
the recess to keep your bracket as close to the
display as possible.
5. Place the spacer between the mounting
and the display.
6. If a smaller screw is being used(M4,M5 or M6), please use a washer with each scr
for added stability
this kit
d lengths.
at surface, and locate the threaded mounting
bracket
F inal Installation
Attach each brack et to the display by aligning the holes on each bracket, with the
threaded inserts on the back panel of
your display, inserting the screws
through both and turning clockwise
until they are fully inserted.
1. Tighten with a Phillips head
screw driver.
CAUTION: Two people are required
for this step.
2. To complete the installation of
your new lcd/plasma mount, carefu
and lower mounting crossbars.
3. Making sure that the safety-bar is not in place when placing the television on the
mount
O pe ration a nd Adjustment
You can adjust the tilt of you
hand side and left-hand side of the TV brackets.
1. First, turn the tension knobs counter-clockwise to loosen the
mounting crossbars.
2. To tilt the mount up, press the right knob as you pull on the lower
part, while at the same time pushing on the upper crossbar to tilt
the mount to the position you want, then release the knob and
push slightly until it locked.
3. To tilt the mount down, press the right knob as you pull on the
upper crossbar, while at the same time pushing on the lower cr
mount to the position you want, then release the knob and push slightly until it locked.
4. Once the desired level of tilt is achieved, retighten the mount by turning the tension
knobs clockwise.
O th er viewing adjustments ca
backward and pulling forward. You can get 30 degree left or right side
view, or make your TV from the wall Max.301mm or Min. 120mm.
Other feature of your display mount is the lock designed to preven
television from being removed from the crossbar. To use the security
function, you only need to thread the screws under the TV brackets till it
locked the bracket tightly.
ew
lly place the television brackets over the upper
r television by using the tension knob located on the right-
n be made by simple pushing your TV rightward, leftward or
o ssbar to tilt the
t your