Anker SOLIX Solarbank 3 E2700 Pro Kurzanleitung

Anker SOLIX
ANKER SCLIX
QUICK
System Overview
This diagram shows the primary system for the whole
8 PV Modules
Max
Anker SOLIX Solarbank 3 E2700 Pro
ANKER
III
5 Expansion Batteries Maxi
3 Installation
Do not place the equipment near an area exposed
direct sunlight, fire, or explosive materials.
Ensure Solarbanl< is off during installation.
ANKER
o
29.2 kg
Prepare Tools (Not Included)
Place the Bottom
Battery
Within Wi-Fi coverage
Solarbank to connect
the network
18 to 47 mm away
Phillips Screw- the wall
driver
pen
(PHI and PH2)
Power Drill
Hammer
(Drill Bit: 8 mm)
4
Electrical Connections
• Ensure Solarbank is off during wiring • To avoid
Solarbanl<
Ensure the unused PV ports on Solar-
point as shown. For wiring
bank are sealed with waterproof caps.
tions, please
Never connect PV modules in series to
user guide.
avoid damage to the equipment.
IIIII I IIIII I I • IIII I III I II I III ' III I
II II I I III I
(Optional) Install the Smart Meter Three-Phase
The three-phase
Scan the QR code to read all the features three types of live wires (LI,
instructions.
L2, and L3).
Smart Meter User Guide
Wear insulating • Turn off the main
gloves (not
breaker before
included) during installation.
the installation.
ON
OFF
1
We recommend finding a qualified electri-
cian for installation
Wiring colors may vary by country or region
5
Device Setup
Power On
The first use requires the connection of a PV module
outlet.
• With solar or AC input: Solarbank turns on automatically. To turn it off,
disconnect it from both the PV modules and the home outlet, and then press
the power button for 3 seconds
• Without solar and AC input: Press the power button for 3 seconds to turn
Solarbank on or off
ANKER
s c LIX
Q.)
ON
Q.) OFF
-W- Refer to the online user guide for the
button controls and
Solarbank 3 E2700 Pro
START GUIDE
home photovoltaic energy cycle Smart
2
Main Panel
Home Outlet
Home Loads
Smart Plug3
Home Outlet
Optional Accessories:
IAnker SOLIX BP2700 Expansion
2Anker SOLIX Smart Meter
3Anker SOLIX Smart Plug
Remove Rubber Plugs
to
Stack
Unfasten screws (if the Top
applicable) and pry
PHI
Stacl< expansion
open the rubber plugs
sequence
top.
24 kg
Expansion
for
to
from
18-47
O
TO avoid water damage, do
mm
not remove the bottom rubber
plug when installing the
bottom expansion battery or
only one Solarbank.
Connect to the Grid
electric shock, ground
using the grounding Connect Solarbank
instruc- outlet
refer to the online
Connection
1. Install the smart meter. 2. Prepare and connect
power system
3. Insert the CT link and snap CTS to the home-side
The CT arrows point from home to the grid.
CT
Ll CT
L2CT
Confirm Networking Status
and a home
Solarbank enters networking mode
on. Ensure the IoT button is flashing
ANKER
SOL IX
Connect to the network using the Anker app within
LED light guide wil turn off.
2 Unboxing
In the Solarbank Box
ANKER
Grid
Anker SOLIX
Solarbank 3 E2700
Schuko Plug (3 m)
pro
Home Loads
o
o
Battery
Wrench for Removing
PV Connectors
Install the Wall Mount Kit
Up with Solarbank at
Attach the L-shape wall mount fittings
of the first expansion battery under
batteries in
with Solarbank at the
o
5. Insert the anchor. 6. Rotate
Connect to Your Device
to a home Power your device directly using
the backup terminal if needed.
AC Cable with
Schuko Plug
(included)
Insert the plug fully into the terminal
Single-Phase Connection
cables.
The single-phase power system
features one live wire type (LI).
Smart Meter Side:
6.5 ± 0.5 mm
L3
0.4 - 1.6 mm
cables.
From Home
1
Ll
To Grid
L3CT L3
Use the Anker App
automatically when powered
1. Download and install the Anl<er app
blue.
Then, sign in or create
30 minutes or Solarbank
Scan for Ful User Guide
In the Expansion Batteryl Box
iOrdered separately.
AC Cable with
Anker SOLIX BP2700
Fixed Bracket
Expansion Battery
Wall Mount
L-Shape Wall Expansion
(M5 60 mm)
Mount Fitting
Documents
to both sides
Solarbanl<
1. Partially tighten the short 2. Mark a pilot hole.
v
screw.
900
OR 18-47
3. Rotate the fitting down. 4. Drill the marked
the fitting back up. 7. Tighten the long screw. 8. Tighten the short screw.
Connect to PV Modules
Direct Connection (Up to 4 PV Modules)
Connect each PV module directly to the same set of PV input ports
9
• Anker SOL IX Solar Panel
Extension Cab e (sold
separately)
I. Install the smart meter.
2. Prepare and connect
00
3. Insert the CT link and snap Ll CT to the home-side Ll cable.
The CT arrow points from home to the grid.
CT
Ll CT
2 Add your Solarbank.
an account.
GET IT ON
Google Play
Google Play and the Google Play logo
are trademarks of Google Inc.
Download on the
App Store
A Ie and the Apple logo are trademarks
o pple Inc.
support@anker.com
(DE) +49 (800) OOO2522
Scan for Videos, FAQ,s and More
Interlocking Kit
Screw
(MS 10 mm)
Documents
Kit
Screw Screw
(MS 10 mm)
Install the
Interlocking Kit
mm
o
hole.
O
1. Snap a fixed bracket in
2. Tighten the screw.
place.
o
g 000
Parallel Connection (Up to 8 PV Modules)
Connect every two PV modules to the same set of PV
input ports
II I:I II
Anker SOL IX
Y Branch Connector
(sold separately)
Smart Meter Light Guide
cables.
Unable to Collect
Q)
Grid Data
Working
Normally
No Wi-Fi / Bluetooth
00
Connection
Smart Meter Side:
05 mm
Grid Data Col ected
Working
04- 1.6 mm
Normally
Wi-Fi / Bluetooth
Connected
Upgrading
From Home I
After electrical connections, the
smart meter powers on
automatically
To Grid
Connect to the network using
the Anker app within 30 minutes
orthe smart meter will turn off.
3 Connect to the networl<.
Add
Important:
update the firmware to
I the latest version.