ACR ZENEC ZE-RVC82MT Montageanleitung

ZENEC
MOUNTING INSTRUC TIONS
MOUNTING INSTRUCTIONS
C) RCA/Cinch
RCA / Cinch
Video Signal (CVBS)
Video Signal (CVBS)
0.70 m
0.70 m
KEY FEATURES
KEY FEATURES
• Compact high resolution universal rear view camera
• Compact high resolution universal
• Robust camera housing made of die-cast aluminum
• Robust camera housing made of die-cast
• Cam sensor with 170° diagonal viewing angle for wide monitoring area
• Cam sensor with 1700 diagonal
behind the vehicle
behind the vehicle
• Vertical 140° image section adjustment by rotating sensor roller, 0° to
• Vertical 1400 image section
70° up / 0° to 70° down
700 up / 00 to 700 down
• High sensitivity CMOS sensor with 0.3 lux light sensitivity for good night
High sensitivity CMOS sensor with 0.3 lux light sensitivity
vision
vision
• 10 m long separable system cable with mini 4-PIN connectors
• 10 m long separable system cable with mini 4-PIN connectors
• Required cable feed-through hole: 6.1 mm, easy mounting via M6
• Required cable feed-through
hollow thread screw
hollow thread screw
• IP69K certified
• IP69K certified
• CAUTION
A CAUTION
■ Use the included connection cable exclusively. Modifying the cable will void
Use the included connection cable exclusively. Modifying the cable will void
your warranty.
your warranty.
■ The camera is water- and dustproof and has been licensed according to the
• The camera is water- and dustproof and has been licensed according to the
international standard IP69K. However, vehicle cleaning using high pressure
international standard IP69K. However, vehicle cleaning using high pressure
water and steam jet devices may still lead to damage of IP69K rated camera
water and steam jet devices may still lead to damage of IP69K rated camera
models by intrusion of water.
models by intrusion of water.
■ If the vehicle is treated with a water jet high pressure cleaning device, make
• If the vehicle is treated with a water jet high pressure cleaning device, make
sure to keep a distance of at least one meter between the water nozzle and
sure to keep a distance of at least one meter between the water nozzle and
the camera sensor / housing.
the camera sensor / housing.
Rotatable Reverse Camera
Rotatable Reverse Camera
Loosen the locking screw of the camera housing side cover.
Loosen the locking screw of the camera housing side cover.
Pull the camera cable out of the rectangular opening in the
Pull the camera cable out of the rectangular opening in the
camera bottom. The accessory set contains one piece of
camera bottom. The accessory set contains one piece of
hollow thread screw, washer, M6 lock nut, M6 spring washer,
hollow thread screw, washer, M6 lock nut, M6 spring washer,
3M adhesive pad and self-tapping fixing screw.
3M adhesive pad and self-tapping fixing screw.
Camera housing
3M adhesive pad
ZENEC by ACR AG ∙ Bohrturmweg 1 ∙ CH-5330 Bad Zurzach ∙ Switzerland, EU Legal Representative: ACR S & V GmbH ∙ Industriestr. 35 ∙ D-79787 Lauchringen ∙ Germany www.zenec.com
ZENEC by ACR AG Bohrturmweg 1
Fuse 0.5 A
Fuse 0.5 A
Red: DC 6 ~ 24 V
Red:
Black: GND
Black:
mini 4PIN mini 4PIN
mini 4PlN mini 4PlN
(female) (male)
(female) (male)
rear view camera
aluminum
viewing angle for wide monitoring
adjustment by rotating sensor roller, 00 to
for good night
hole: 6.1 mm, easy mounting via M6
Insert the cable into the groove from the hollow thread
Insert the cable into the groove from the hollow thread
screw. Route the cable with the hollow thread screw into the
screw. Route
round hole in the camera base. Drill a mounting / cable
round hole in the camera base. Drill a mounting / cable
cable feed-through hole with a diameter of 6 mm. Fix the
cable feed-through
cam via hollow threaded screw with washer, spring washer
cam via hollow threaded screw with washer, spring washer
and M6 lock nut.
and M6 lock
Cylinder
Side cover
Hollow
screw
CH-5330 Bad Zurzach - Switzerland, EU Legal Representative.
DC 6 & 24 V
GND
10.0 m
10.0 m
mini 4PIN
mini 4PlN
(female)
(female)
TECHNICAL SPECIFICATIONS
TECHNICAL
Image device:
Image device:
Lens focal length:
Lens focal length:
area
TV system:
TV system:
View angle:
View angle:
Native sensor resolution:
Native sensor
Resolution of video-out:
Resolution of video-out:
Signal to noise ratio:
Signal to noise ratio:
Light sensitivity:
Light sensitivity:
Video output:
Video output:
White balance:
White balance:
Backlight compensation:
Backlight compensation:
Gamma correction:
Gamma correction:
Gain control:
Gain control:
Sync system:
Sync system:
Power supply:
Power supply:
Current consumption:
Current consumption:
IP protection rating:
IP protection rating:
Operating temperature:
Operating temperature:
Dimensions (WxHxD):
Dimensions (WxHxD):
the cable with the hollow thread screw into
hole with a diameter of 6 mm. Fix the
nut.
Cable
ACR S & V GmbH
ZE-RVC82MT ZE-RVC82MT
ZE-RVCB2MT
RE AR VIE W C AMER A
REAR
Camera rotates
Camera
0.70 m
0.70
mini 4PIN
mini 4PlN
(male)
(male)
SPECIFICATIONS
6.09 mm SONY IMX225LQR CMOS sensor
6.09 mm SONY IMX225LQR
f 1.8
f 1.8
NTSC / 30 fps
NTSC / 30 fps
170° (D) x 135° (H) x 90° (V)
1700 (D) x 1350 (H) x 900 (V)
1305 (H) x 977 (V) pixels
resolution: 1305 (H) x 977 (V) pixels
> 420 TV lines
> 420 TV lines
> 48 dB
> 48 dB
0.3 Lux
0.3 Lux
1.0 Vp-p, 75 ohms CVBS
1.0 vp-p, 75 ohms CVBS
Auto
Auto
Auto
Auto
0.45
0.45
Auto
Auto
Auto
Auto
DC 6 – 24 V
DC 6-24 V
70 mA @12 VDC, ≤ 480 mW
70 mA VDC,
IP69K
IP69K
-30° C ~ +75°C, RH 95% max.
-300 C - +750C, RH
44 x 23 x 29 mm
44 x 23 x 29 mm
Alternatively, the camera can be fixed with the 3M adhesive
Alternatively, the camera can be fixed with the 3M adhesive
pad or the self-tapping screw. The cable must always be
pad or the self-tapping screw. The cable must always be
the
routed though the round hole in the camera base to provide
routed though the round hole in the camera base to provide
for full adjustment range of the sensor cylinder. Loosely
for full adjustment range of the sensor cylinder. Loosely
screw on the housing cover and align the camera. Tighten
screw on the housing cover and align the camera. Tighten
the locking screw well.
the locking screw well.
Cylinder
E13 IOR-06 16586
Industriestr. 35 D-79787 Lauchringen
VIEW CAMERA
rotates
m
CMOS sensor
480 mw
max.
- Germany www_zenec.com