Cleaning And Maintenance - Uniprodo Uni-Humidifier-05 Benutzerhandbuch

EN
1. ON/OFF button
2. Timer button
3. Fan speed button
4. Backight button
REMOTE CONTROL
1
2
3
4
1. ON/OFF button
2. Backlight button
3. Fan speed buttons
4. Timer buttons
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The temperature of environment must not be higher
than 40°C and the relative humidity should be less than
85%. Ensure good ventilation in the room in which the
device is being used. There should be at least 30 cm
distance between each side of the device and the wall
or other objects. There must be a minimum of 50 cm
free space above the device. Keep the product away
from hot surfaces. The device should always be used
when positioned on an even, stable, clean, fireproof
and dry surface, and be out of the reach of children
and persons with limited mental and sensory functions.
Position the device such that you always have access
to the power plug. The power cord connected to the
appliance must be properly grounded and correspond
to the technical details on the product label.
3.3. DEVICE USE
TURNING THE DEVICE ON:
1. Connect the device to the power supply. The user
hears a long beep.
2. Press the ON/OFF button to turn the device on.
The user will hear a single beep and the fan speed
LED will light up.
3. Setting the fan speed:
• While the device is running, press the fan speed
button. The user will hear a single beep.
• Press the fan speed button again to set the
desired operating mode: SLEEP – MED-HIGH
(SLEEP – MEDIUM MODE – HIGH MODE). The
user will hear a single beep each time. The LED
corresponding to the selected operating mode
will light up.
• CAUTION: In the SLEEP mode, after 5 seconds of
inactivity, all lights and backlights will turn off.
After pressing any button, the LEDs will light up.
10
4. Setting the timer:
• While the device is operating, press the timer
button to select the desired operating mode:
2H, 4H, 8H. The user will hear a single beep each
time. The LED corresponding to the selected timer
mode will light up.
• Press the timer button again to deactivate preset
settings. The device will continue to work.
• When the selected timer mode expires, the device
and all LEDs turn off.
5. Setting the backlight:
• While the device is operating, press the backlight
button. The user will hear a single beep.
• The backlight will switch between blue - turquoise
- green - yellow - orange - red - purple.
• Press the backlight button to select a desired
color.
• Press the backlight button again to switch the light
off.
6. Press the ON/OFF button to turn the device off.
The user will hear a single beep and all LEDs will
turn off.
CAUTION! Empty the water tank after each use
and let it dry! Leaving water in the tank may cause
bacterial growth.
DEHUMIDIFIER FILTER INSTALLATION
CAUTION!
1. Before replacing the filter, turn the device off and
unplug the power cord.
2. Make sure that the filter is correctly inserted.
3. Use only filters dedicated to a given device!
4. When the device detects that the filter is spent,
the LED turns red.
5. Regularly remove the dust from the filter. Do not
soak the filter in water or any other liquid.
Turn the device off and remove the cord from the power
socket.
1. Turn the device upside down and turn the base in
the shown direction.
2. Pull out the spent filter.
3. Remove the protective foil from a new filter.
4. Install a clean filter.
5. Mount the base: press down and turn the base in
the shown direction.
* After replacing the filter, connect the device to
the power socket, then hold the ON/OFF button
for 7 seconds to reset the device.
CAUTION! Before using it for the first time, do not
reset the device. Just remove the foil from the
filter, install it in the device and turn the device on.
1 2
4 5
HUMIDIFIER OPERATION
* Before the first use, remove the protective foil from
the filter in the water tank. Install the humidifier filter
in the water tank.
1. Remove the entire element of the humidifier and
place it on an even surface.
2. Remove the water tank lid.
3. Pour in the correct amount of water. Be careful
not to exceed the maximum water level! Do not
pour water above the overflow holes level on both
sides of the tank.
4. Place the lid back on the tank.
5. Place the entire humidifier element on the air
purifier.
6. Operate the device with the remote control.
7. Allow to dry after use. Make sure that the
humidifier filter is also completely dry.
* When using a humidifier, the filter in the water
tank may slightly turn yellow. This is not a defect.
It is recommended to replace the humidifier filter
every 3 months of regular use or if the filter color
changes significantly.
CAUTION! Do not tilt the device when the tank is
full.

3.4. CLEANING AND MAINTENANCE

a) Always unplug the device before cleaning it.
b) Use only non-corrosive cleaners to clean the
surface.
c) After cleaning the device, all parts should be dried
completely before using it again.
d) Store the unit in a dry, cool place, free from
moisture and direct exposure to sunlight.
e) Do not spray the device with a water jet or
submerge it in water.
f) The device must be regularly inspected to check
its technical efficiency and spot any damage.
g) Use a soft, damp cloth for cleaning.
h) Do not use sharp and/or metal objects for
cleaning (e.g. a wire brush or a metal spatula)
because they may damage the surface material of
the appliance.
i) Do not clean the device with an acidic substance,
agents of medical purposes, thinners, fuel, oils
or other chemical substances because it may
damage the device.
j) Clean the water tank regularly.
k) Do not clean the filter with a vacuum cleaner or
directly under water!
l) It is recommended to regularly expose the filter to
the sun to decontaminate it.
m) If the device is not used for a long time, make sure
that the water tank is empty and that the device is
3
dry.
n) When not in use, store the device covered, e.g. in
a bag or cardboard box.
11 EN
DISPOSING OF USED DEVICES
Do not dispose of this device in municipal waste systems.
Hand it over to an electric and electrical device recycling
and collection point. Check the symbol on the product,
instruction manual and packaging. The plastics used
to construct the device can be recycled in accordance
with their markings. By choosing to recycle you are
making a significant contribution to the protection of
our environment.
Contact local authorities for information on your local
recycling facility.