Warranty Conditions; Installation Instructions - Screenint Compact Installationsanleitung

INSTALLATION MANUAL - COMPACT - ELLIPSE - MAJOR
INDEX
- SCREEN MOTOR END STOP ADJUSTMENTS: see attached specific document
- USE OF OPTIONAL INTERFACES: see below - point 2 – Electric Connection
- TROUBLESHOOTING: in case of waves on the surface, proceed as per Tutorial on YouTube channel EuroscreenSrl
WARNINGS
Before installing the screen, please read the following instructions carefully. We would recommend that these instructions are stored safely for future reference.
When opening the packaging of the screen, please DO NOT USE CUTTERS or OTHER SHARP TOOLS that can damage the screen inside. During opening the packaging and during
installation, it is recommended to use work gloves. Depending on the screen weight, it has to be handled by at least two or three persons taking care to the following ratio
KG/PERSON: MALE 25 kg. – FEMALE 15 kg. The manufacturer does not take responsibility for any damage to property or personal injury if the screen is used outside of
recommended specifications or in case of incorrect/poor quality installation.
CERTIFICATIONS
Motorized screens Compact, Major, Ellipse are
The surfaces for projection used on the products are cadmium-free and are fire-proof certified as follows:
- class M1 – MATTE WHITE, CINESOUND, FRONTREAR, REAR PLUS
- class M2 – WHITE, LUMI-GREY, LUMI GREY MICROPERFORATED, MICROPERFORATED, BRIGHT CONTRAST 3D 0.8
class B1 – WHITE, MATTE WHITE, BRIGHT CONTRAST 3D 0.8, FIBRE MATTE

WARRANTY CONDITIONS

This projection screen is guaranteed 2 years from the purchase date for manufacturing defects and 5 years on motor defects.
Responsibility is limited to repairing or substitution of the defected components and without any other charge at our expense.
Warranty is officially voided if the screen has been dismantled or it is returned with collision damage or defective due to incorrect installation. Repairs must be carried out by
an Approved ScreenInt Certified Engineer.
Warranty is officially voided if (all the following cases are including but not limited):
1) defects not due to deficiencies in the material or workmanship;
2) amendments, alterations, repairs or disassembling of the Product not previously authorized in writing by Screenint;
3) installation, use or maintenance of the Product not in compliance with Screenint 's instructions as set forth in this Installation Manual and/or in any other technical
documentation supplied together with the Product;
4) bad and/or improper and/or not in compliance installation, maintenance, negligence, improper use;
5) use of non-original spare parts or not authorized in writing by Screenint;
6) normal wear and tear;
7) the motor is removed / dismantled;
8) the screen has been damaged in transit;
9) the instructions regarding the electrical connections have not been followed;
10) the products have to be installed following the electric regulations (CEI) and the other local specific laws;
11) in the installation are used electric interfaces that does not allow the correct time lapse between up and down operation (complete cut down of electric power on
both phases for one second)
12) electrical accessories have been used that are incompatible with the screen motor causing damage to its internal components;
13) the motor end stops have been modified without the authorisation of the factory;
14) the sticker regarding the serial number of the product has been altered, deleted, removed or tampered.
DO NOT install this screen nearby or over heating or air conditioning systems, because PVC is a plastic material which dilates and remains damaged if it is subjected to heat
and/or cool air.
DO NOT install this screen either facing direct sun light or blocking a window as PVC could be damaged and make waves for the explanations given above.
The PVC cloth is very sensitive to temperature range. We advise to mount the screen in environments with an ambient temperature in the range of 20°-25°C.
We advise you to WAIT 3 HOURS for the SCREEN to ACCLIMATISE BEFORE MOUNTING AND ROLLING DOWN the screen after delivery, especially if screen arrives from a cold
temperature.
In case at the first roll down, the screen shows waves, check temperature of the room. Roll up the screen again and leave it closed for 24 hrs at ambient temperature of 20-
25°C, in order to improve flatness.
THE SCREEN HAS TO BE STOCKED AND TRANSPORTED ALWAYS IN HORIZONTAL POSITION, otherwise there could appear waves on the projection cloth.
DO NOT WASH the projection surface with alcohol or solvent nor with commercial cleaners. Every now and then dust the surface with a dry and clean duster.
Please, be very careful because any kind of stain on projection surfaces is inerasable.
The screen has to be used showing the total projection sizes indicated on the packaging; therefore it is NOT allowed to adjust the end stops to restrict the total drop or extend
it. Restricting the total drop of the screen is likely to cause your screen surface to lose its flatness.
When the screen is not completely rolled down (as by factory setting), flatness of the cloth is NOT guaranteed and therefore not covered by warranty.
DO NOT HANG TO THE SCREEN and DO NOT HANG ANY OBJECT to it. Please take care that children DO NOT PLAY with the screen as they can get severely injured.
The manufacturer will not accept returns of screens for repair without manufacturer's authorization (RMA number) and without a suitable packaging.

INSTALLATION INSTRUCTIONS

1. ASSEMBLY
The product has to be installed and used conform to the laws in force within the country where the product is used.
Our screen is supplied with ceiling/wall brackets suitable for fixing it on the wall or ceiling by heavy duty bolts that are supplied in the packaging (Fig. 1). During installation,
please take care to use security belts in order to secure the screen housing.
WARNING: DO NOT INSTALL THE SCREEN NEAR HEATING SOURCE BECAUSE IT DAMAGES THE PROJECTION SURFACE. Prior to installing the roller screen, ensure the ceiling/wall
is suitable for the loading induced by the weight of the screen. Take particular care if the construction is timber or stud partitioning. If in doubt, seek the advice of a structural
engineer. Please be aware that the screen is heavy and two or more people may be required to lift it safely. Fix the brackets to the wall/ceiling, insert the clamp screws into
the threaded holes on the front of the fixing brackets, hook roller case in tab on bracket and tighten the clamp screws to the front groove to lock the screen in position (Fig. 2).
Release the screen transport straps. Cut and release the screen from the ribbon that keeps the bottom bar tightened. At the end of the installation, please check that the
motorized screen is perfectly level.
CAUTION: CHECK EVERY 6 MONTHS THAT SCREWS, WALL PLUGS AND BRACKETS ARE IN GOOD CONDITIONS AND WELL TIGHTENED.
2. ELECTRIC CONNECTION
Connection of the power supply must be carried out by qualified personnel only, using the diagram showed on Fig. 3. Pay attention to wire colours and fix the switcher near
the screen as we recommend the projection surface is visible to the operator. Never connect more than one screen motor and/or lift motor to the same switcher. Use the
supplied switcher only. IN CASE OF MAINTENANCE, UNPLUG THE POWER SUPPLY.
In case the screen is controlled via optional interfaces:
1- The optional interfaces has to be supplied by ScreenInt or by a well-known tubular motor manufacturer
2- Take care that the control system is programmed so there is no tension on the interface output for at least 1 sec. during switching between rolling up and rolling down
.
operations and viceversa
IT IS FORBIDDEN TO STAY UNDER THE PROJECTION SCREEN.
IT IS FORBIDDEN TO USE THE PROJECTION SCREEN OUTDOOR
rolled down can cause deformations to the projection surface.
certified.
.
ONCE PROJECTION IS FINISHED, ROLL UP THE SCREEN (keeping the screen