Seav RTX 2251 Handbuch Seite 16

——————————— PROGRAMMING MENU ————————————
LED Reference LED Off
1) TEST Test Saf. Dev. = OFF
2) CODE 1 CH1 No Pgm. Code
3) CODE 2 CH1 No Pgm. Code
4) CODE 3 CH1 No Pgm. Code
5) CODE 1 CH2 No Pgm. Code
6) CODE 2 CH2 No Pgm. Code
7) CODE 3 CH2 No Pgm. Code
1) TEST (RTX 2251 (Base) device functional test).
Functional test of RTX 2251 (Base) device, if combined with motor control unit equipped
with Safety Devices test (see "RTX2251-DEVICE TEST" paragraph).
Test enabling on the Device is carried out as follows: press SEL and TEST LED will start
to flash. Press SET, the TEST LED remains on and programming is complete. Repeat the
procedure to restore previous configuration without active TEST.
2) CODE 1 CH1 Programming of n.1 RTX 2252 Sensor transceiver device coupled with CH1)
The n.1 RTX 2252 (Sensor) Transceiver Device coupled with CH1 of RTX 2251 (Base) Trans-
ceiver Device, is programmed as follows: press SEL and CODE 1 CH 1 LED starts flashing;
the Base broadcasts to all Sensors, searching for one to be memorised: press SET key of
the Sensor you want to program to send the memorisation confirmation code ( TX LED
makes 5 quick flashes); CODE 1 CH LED remains on and programming is complete. The
Base device exits programming if no confirmation code is received within 15 seconds.
Deletion The memorised code is deleted as follows: press SEL and CODE 1 CH1 LED
starts flashing; press SET, CODE 1 CH1 LED switches off and the procedure is complete.
3) CODE 2 CH1 (Programming of n.2 RTX 2252 Sensor transceiver device coupled with CH1)
Proceed as described in point "2) CODE 1 CH1" to program the transmission code of n.
2 RTX 2252 (Sensor) Transceiver Device coupled with CH1 of RTX 2251 (Base) Trans-
ceiver Device.
4) CODE 3 CH1 (Programming of n.3 RTX 2252 Sensor transceiver device coupled
with CH1).
Proceed as described in point "2) CODE 1 CH1" to program the transmission code of
n.3 RTX 2252 (Sensor) Transceiver Device coupled with CH1 of RTX 2251 (Base) Trans-
ceiver Device.
5) CODE 1 CH2 (Programming of n.1 RTX 2252 Sensor transceiver device coupled with
CH2)
Proceed as described in point "2) CODE 1 CH1" to program the transmission code of n.1
RTX 2252 (Sensor) Transceiver Device coupled with CH2 of RTX 2251 (Base) Transceiver
LED On
Device.
Test Saf. Dev. = ON
Code 1 on CH1 Pgm 6) CODE 2 CH2 (Programming of n.2 RTX 2252 Sensor transceiver device coupled with
Code 2 on CH1 Pgm. CH2)
Code 3 on CH1 Pgm.
Proceed as described in point "2) CODE 1 CH1" to program the transmission code of n. 2
Code 1 on CH2 Pgm.
RTX 2252 (Sensor) Transceiver Device coupled with CH2 of RTX 2251 (Base) Transceiver
Code 2 on CH2 Pgm.
Device.
Code 3 on CH2 Pgm.
7) CODE 3 CH2 (Programming of n.3 RTX 2252 Sensor transceiver device coupled with
CH2)
Proceed as described in point "2) CODE 1 CH1" to program the transmission code of n.3
RTX 2252 (Sensor) Transceiver Device coupled with CH2 of RTX 2251 (Base) Transceiver
Device.
RESET
Keep the SEL and SET keys simultaneously pressed for more than 2 seconds so that all
indicator LEDs briefly switch on at the same time accompanied by three quick Buzzer
Beeps, if the device must be reset to company configuration.
16