Balluff BAE0004 Betriebsanleitung Seite 2

BALI-UFF
sensors
Technical
Installation and Operating
Din Rail Mountable
Switching Power Supply
BAE0004
Ordering Code
BAE PS-XA-1W-24-012-002
Part Number
Ill
A Safety notes
Read Instructions!
Before working with this unit, read these instructions
carefully and completely. Make sure that you have
understood all the information!
Disconnect system from supply network
Before any installation, maintenance or modification
Disconnect your system from the supply network. Ensure that
cannot be re-connected inadvertently!
Before start of operation
Ensure appropriate installation
Warning! Improper installation / operation impair safety and
result in operational difficulties or complete failure of the unit.
The unit must be installed and put into service appropriately
by qualified personnel. Compliance with the
relevant regulations must be ensured. Before operation
begun the following conditions must be ensured, in particular:
• Connection to main power supply in compliance
VDEOIOOO and EN50178.
• With stranded wires: all strands must be secured
terminal blocks (potential danger of short circuit)
Unit and power supply cables must be properly fused; if
. necessary a manually controlled disconnecting
be used to disengage from supply mains.
. The non-fused earth conductor must be connected
"O " terminal (protectionclass I).
• All output lines must be rated for the power supply output
current and must be connected with the correct polarity.
• Sufficient air-cooling must be ensured.
• Use in a pollution degree 2 environment.
In operation: No modifications!
As long as the unit is in operation: do not modify the
installation! The same applies also to the secondary
of electric arcs and electric shock (fatal)!
Only (dis) connect plug connectors
the power is off!
Convection cooling
Do not cover any ventilation holes!
Leave sufficient space around the unit for cooling!
See supplementary sheet "Technical Data" and Fig. 1
Warning: High voltage! Store energy!
The unit contains unprotected conductors carrying a lethal
high voltage, and components storing substantial
energy. Improper handling may result in an electric shock or
serious burn!
• The unit must not be opened except appropriately
personnel!
• Do not introduce any object into the unit!
• Keep away from fire and water!
Fig. 1
worldwide
Out-
put
Data
Fig. 2
Balluff GmbH
Schurwaldstraße
73765 Neuhausen
Germany
Fon +49
Fax +49
balluff@balluff.de
www.balluff.com
Installation
Application
This unit is a primary switched-mode
for use in panel-board
applications
hazard protection).
service appropriately
Mounting
Mounting
Permissible mounting position: see Fig. I keep free ventilation
work:
hole, leave space for cooling! Recommended
free space at all sides for ventilation / cooling:
see supplementary
Snap on support
• Tilt the unit slightly rearwards.
• Fit the unit over top hat rail.
• Slide it downward
Press against the bottom front side for locking.
Shake the unit slightly to check the locking action.
Front elements
is
Operation
with Indicates whether the unit is working properly. Green LED is
on in normal operation and goes out if shutdowned.
in the Potentiometer
Setting the output voltage.
element must
to the
Connection
Connection
• Data for permitted
see enclosed leaflet " Technical Data " (See Fig. 3).
• Use only commercial
voltage and current values!
• With flexible
secured in the terminal.
Slde. • Risk
• Ensure proper polarity at output terminals!
Grounding
when
• Do not operate
EMC and safety standards
must only be operated if the PE terminalO is connectedto
the non-fused
• Secondary side is not earthed; if necessary the @ or e
terminal can be earthed optionally.
Internal fuse
• The internal input fuse serves to protect the unit and must
not be replaced by the user. In case of an internal defect, the
unit must be returned to the manufacturer
amounts of
Removal
trained Removal Deatching from support rail
• Before removal:
your system
(See Fig. 4) push the slider
lower front edge of the unit (tipping)
BALLUFF
00 00000000
0000000
00 00000000
eee
000
00000000
0000000
0
000000000
000000
ln-
put
0000000000 QQCIÜOOO
OO QQOOOOOOOOQOÜOO
00000000000000000
OO OOOOOOOOOOOQOOO
00000000000000000
00000000000000000
9
a.
7158 173-0
7158 5010
power supply designed
installations or building-in
where access to the supply is restricted (shock-
It must only be installed and put into
by qualified personnel.
to have 25mm
sheet "Technical Data".
rail (SeeFig. 2)
until it hits the stop.
indicator
I Internal fuse
loads, cable cross-sections and stripping:
cables designed for the indicated
cables: make sure that all stranded cable are
without PE connection! To comply with
(CE mark, approvals), the unit
earth conductor.
for safety reasons.
Switch mains power off and disconnect
from the supply network.
downwards (unlock), Gently
and remove.
Fig. 3
mm
Connector size range:
AWG26 - 12 / - mrn2
- Connector can withstand
torqe at maximum
5 pound-inches
Use copper conductors
only 60 / 75'C
Max. surrounding air temperature
of 50 oc for UL 508
Fig. 4
00
O
00
z
Technical All specifications are typical at nominal line voltage,
full load, 25QC. Unless
Data
BAE0004
Ordering Code
BAE
Part Number
General
Switching frequency
Isolation voltage
Isolation resistance
Power up delay
Ambient temperature
Derating
Storage temperature
Relative humidity
Cooling
Dimension (W x L x D)
Weight
Input specifications
Input voltage
Input voltage range
Inrush current
Line frequency
Input fuse
Output specifications
Output voltage . 24 VDC
Output current
Output wattage
Voltage trim range
Output voltage accuracy
Line regulation
Load regulation
Settling time
Temperature coefficient „
Ripple & noise
Hold up time
DC ON Indicator
DC LOW Indicator
Parallel modus
Efficiency . 86%
Rated over load protection
Output short circuit
Approval and standards
UL / cUL UL 508 Listed / UL 60950-1 , UL 1310 Class 2
TÜv
EN 60950-1
CE EN 61000-6-3,
EN 61000-3-3,
EN 61000-4-2,
EN 61000-4-5,
EN 61000-4-11
Fig. 5 Derating
100
*
75
-25 61 71
lift
Temperature ( oc ]
gee
eee
00
00
BALLUFF
otherwise noted
PS-XA-1W-24-012-002
> 80 kHz
3.000 VAC
100 MQ
< Is
-+710C
-2.5 0/0 rc from +61 oc
-25 oc +85 oc
20 - 95 % RH
. Free air convection
41.0 x 90.0 x 114.0 mm
0.29 kg
100 - 240 VAC
85 - 264 VAC / 90 - 375 VDC
. 115
47 - 63 Hz
T2 A/ 250 VAC internal
1.25 Amps
30 WATTS
24.0 - 28.0 VDC
< 0.5 0/0
< 0.5%
1 ms
±0.03 0/0/ oc
50 mV
115 VAC > 20 ms / 230 VAC > 30 ms
Green LED
Over diodes
110- 140 %
Fold forward
EN 55022 Class B, EN 61000-3-2,
EN 61000-6-2, EN 55024,
EN 61000-4-3, EN 61000-4-4,
EN 61000-4-6, EN 61000-4-8,
, EN 61204-3
BALLUFF
DM235-AO