Werbung
Verfügbare Sprachen
Verfügbare Sprachen
The device may not be opened.
Use only at weatherproof places.
The product complies with the electromagnetic compatibility (EMC) requirements
of the current European guidelines. Conformity has been established and the
relevant documentation has been deposited by the manufacturer. Operation
without licence, fee or declaration is permitted within the European Union and
Switzerland
1 Appropriate use
With the SHR-7 FUGA receiver, your garage door control is operable with any
number of Sender SHT-7. Only voltages < 40 V may be switched with the switch
contact (led out cable). It replaces or complements the key provided by the drive
manufacturer or the remote control for controlling the door drive.
The danger of possible faults occurs at the radio connections. This should be
taken into consideration for uses that can affect the safety of human beings.
2 Safety Precautions
Please read, and abide by, the recommendations contained in
these operating instructions. Damage caused by incorrect
application or by failure to follow these operating instructions is
not covered by warranty.
The manufacturer will under no circumstance be held responsible for further
or consequential damage that may be attributed to direct or indirect use of
this product. All changes or modifications not expressly approved by the
manufacturer will void the warranty.
For reasons of safety and conformity (CE) it is not permitted to modify or
•
change parts of the product.
Repair or any kind of soldering on the circuit board is forbidden.
Connect only to a clean, stable mains power source 230V~/50Hz (refer to
•
technical data)
A conveniently located mains isolator must be installed into the mains circuit
•
for hard-wired components.
The electrical system must be equipped with an over current trip, rated at 6A.
•
Electrical devices should be out of reach of children. Please be extra careful if
•
children are around.
For commercial use, compliance must be made with the recommendations
•
and instructions of the responsible regional/national authorities.
Product operation and maintenance must be performed under the supervision
•
of authorised, qualified personnel.
Opening the product and installation has to be performed by authorised
•
electricians only.
The product must not be installed or used in places where a risk of explosion
•
may exist.
Using the receiver during periods where there is a risk of lightning storms is
•
not recommended and is done at the users own risk
The receiver is a state-of-the-art product. However, there is a risk of danger if
•
installation or operation is performed by unqualified personnel
3 System operating range
The system is designed for a large operating range. Walls including steel
reinforced concrete can be penetrated. The maximum range can be achieved
under optimum conditions and by line-of-sight contact between transmitter and
receiver without disruption by external high frequency disturbances.
The following are possible causes that could reduce range of operation:
Obstructing buildings, vegetation or other factors will substantially reduce the
•
operating range.
The distance between the antenna and the operator's body or other
•
conducting objects (e.g. Earth) may influence the working range.
Background "electrical noise" could be relatively high so that the signal-to-
•
noise-ratio may decease and therewith the operating range. Also other
devices, with similar operating frequency, operated in the neighbourhood of
the receiver may reduce the sensitivity.
Operating the receiver adjacent to badly shielded electronic components (eg
•
PC's) that can produce electromagnetic distortion, may severely reduce the
range of operation and could result in intermittent operation.
Caution: To avoid influence of "electrical noise" from the load connected to
the receiver (e.g. DC-Motor) install the receiver within a distance of 1 m.
4 Commissioning
Pull out the plug
•
of the garage door drive
from the socket.
Connect the 2m long cable mounted on the SHR-7 FUGA to the switch input
•
of the garage door drive or at an existing indoor button or key switch.
(GB)
Plug in the SHR-7 FUGA
•
in the previously used
socket and insert the
plug of the garage
door drive into the socket
of the SHR-7 FUGA.
Open the sender (separate operating instructions enclosed) and configure an
•
individual coding. Then close the sender again.
Push the "learn" button with a pen. The LED next to it then flashes at one
•
second intervals.
Press only the desired button of your remote control. As soon as the SHR-7
•
FUGA has learnt the code, the LED blinks faster.
Wait till the LED goes out. Now you can push the button of the remote control,
•
that you have trained, to control the garage door drive.
5 Further information
You can use any number of senders with the same code configuration.
SHR-7 FUGA always functions with the button that has been trained. Therefore,
you can, for example, use another SHR-7 FUGA for your second door and operate
it with another button.
SHR-7 FUGA can however also learn a second code (configuration at the remote
control). Thus, it is possible to control a common courtyard entrance with different
remote controls and only the "correct" sender can activate the garage door.
When you configure a third code, the code that was configured first is deleted.
When you want to delete both the configured codes, you only need to learn
another code twice.
Coordonnées techniques
Fréquences d'utilisation
Sortie
Puissance de coupure
Antenne
Alimentation
Consommation
Température de travail
Dimensions
The cable may be used only for connection to the switch
input of the control. Never use for switching 230V.
00371.93 / SHR-7 FUGA
433,92 MHz
1 contact de fermeture libre de potentiels
(impulsions)
30V DC / 5A max.
230V / 50 Hz
environ 3 VA
De -20
96 mm x 64 mm x 49 mm (sans fiche et câble)
integrée
o
o
C à +65
C
Werbung
