Phoenix KC0300E Bedienungsanleitung

CODES - THE BASICS
•
The KitLock has four code levels available:
i) Master Code
ii) Sub-Master Code
iii) User Code
iv) Technician Code
•
The KitLock is supplied with two factory set codes:
Master Code: 11335577
User Code: 2244
•
When fitted, immediately change the Master Code and User Code.
•
All Master Codes and Sub-Master Codes are 8 digits long.
•
All User Codes are 4 digits long.
•
All Technician Codes are 6 digits long.
•
The lock 'open' time is set at 4 seconds.
FUNCTIONS
Before programming, select the most appropriate function for the application: A) or
B) - See special Master Code set up commands.
A) PRIVATE USE
Important Note: This is the default function and is already pre-programmed in new
locks. This is the most common function and is used where the same code will be
repeatedly used.
B) PUBLIC USE
The user enters their own personal four-digit code twice, the second time to confirm
the correct code. This locks the lock. The same code is entered once only to open
the lock before being erased and ready for the next new user. This function is used
for short term, multi occupancy applications, e.g. a locker in a leisure centre.
OPERATING INSTRUCTIONS
Note: The KitLock has a 10 button keypad and a # button. The # button is hidden
beneath the handle when in the locked position.
Blue LED = Code accepted | Red LED = Code rejected
CODES The lock has the following code levels:
MASTER CODE
The Master Code can:
•
Open the lock
•
Change the Master Code
•
Set / Change / Delete the Sub-Master and User Code
•
Select between Private and Public Functions
•
Activate/deactivate Technician Code
SUB-MASTER CODE
The Sub-Master Code can:
•
Open the lock
•
Change the Sub-Master
•
Set / Change / Delete / the User Code
USER CODE
The User Code can:
•
Open the lock
•
Change the User Code
TECHNICIAN CODE
The Technician Code can:
•
Open the lock
A code cannot be programmed into more than one level.
LOST CODE PROCEDURE
Note: The procedure requires the door to be open
•
Remove the rear-fixing bolt and swing the lock over the edge of the
door to reveal the battery compartment.
•
Remove one battery.
•
Press and hold the 1 button, replace the battery, the Blue LED will flash twice,
release the 1 button. Within three seconds press the 1 button three times. The Blue
LED will flash twice and the lock will have reverted to the factory Master Code 55 44
33 22 and all other stored settings will be erased.
PENALTY TIME
•
Entering three incorrect codes will cause the lock to shutdown for
10 seconds.
Phoenix Safe Company: Where peace mind is guaranteed
KC0300E, KC0500E & KC0600E
OPERATING INSTRUCTIONS
BATTERY POWER
•
The KitLock should provide well in excess of 15,000 openings,
of 4 seconds each, from 2 x AAA 1.5v cells (batteries supplied).
LOW BATTERY
•
When the battery power is low the
•
Red LED will flash 3 times before the
•
Blue LED lights, accepting the code. Fit new batteries as soon as this
happens. The lock will operate for 100 times with low battery.
•
Code accepted
•
Code rejected low battery indication
Code rejected •
low battery indication
BATTERY FAILURE OVERRIDE
The KitLock has been designed so an external PP3 battery can be placed against
the contact points surrounding the Blue and Red LED's so the lock can be opened to
replace the batteries should they fail.
The procedure is as follows:
•
Place the contact points of the PP3 battery against the contact points surrounding
the Blue and Red LED's.
•
The positive + PP3 terminal against the Red LED contact point and the negative
– PP3 terminal against the Blue LED.
•
Enter the Master Code.
•
The motor will withdraw the locking pin allowing the lock to be opened.
•
Fit new batteries by removing the upper fixing bolt and swinging the lock down
over the edge of the door. Refit the lock.
PROGRAMMING
To program – the lock must be in the open position with the # button visible. Every
program command must commence by pressing the # button, followed by either the
Master Code, Sub-Master Code or User Code.
MASTER CODE COMMANDS
CHANGE THE MASTER CODE
#Master Code • 01 • New Master Code
Example: #11335577 • 01 • 12345678
Result: Master Code has been changed to 12345678.
SET OR CHANGE THE USER CODE
#Master Code • 02 • User Code ••
Example: #11335577 • 02 • 9999 ••
Result: New User Code 9999 now operative.
• Code accepted
• New Master Code ••
• 12345678 ••
1