urmet GROTHE RL300FV Bedienungsanleitung Seite 3

Connection to the power supply:
1. Note: This unit must be installed according to local Wiring Regulations and Code of Practice.
2. Ensure the supply is disconnected at the distribution
3. Study the wiring diagram below before making any electrical connections. Incorrect wiring of the unit
could destroy the unit.
4. Connect blue wire from the supply circuit (neutrals) to terminal (N).
INDOOR
Connection
CONTROL
Diagram
SWITCH
BROWN 1 BLACK
Lamp
BLUE
Note: Power cord sepc: 2 x H05RN-F 3C/2C 1.5mm2 max.
Initial set up and operation:
1. After connection to mains power, 60 seconds is required to warm up. The lighting last approximately 60 seconds.
2. Walk in front of the detector until the light comes up. This checks the operation of the detector and the field of
view. Under test mode RedLEDand lighting will come on for 3 seconds when each movement is detected.
3. Repeat Step 2 and adjust the angle of the dome lens until the optimum
4. Turn the Time and Ambient Light (LUX) control to the desired positions.
5.The detector is now in Auto Mode and will operate according to the preset time and ambient light (LUX)
adjustment. LED indicator will keep flashing at stand by-mode. Once activated, LED indicator and lighting will
remain on until timer out.
6. Lights Permanently Off. Turn the power switch off or unplug the AC plug.
Trouble Shooting:
1. Unit will not function at all/Lights won't come on
- Check wiring to make sure that you have correct AC power at the unit.
- Checkthe wiring from the unit to the source of power to make sure you have wired the unit correctly
- Check the ambient light control to see i fit was at your desired level.
2. Detector clicks but does not work
- Check if LEDs are broken.
3. Lights go on and off quickly
- Ensurelight and heat are not being reflected onto the detector. Checkfor white or reflective surfacesthat may be
causing the problem.
- Note the detector is more sensitive in cold weather.
4. Lights stay on
- Recheck the wiring diagram.
-Adjust time to minimum, and ensure unit is firmly fixed to a solid object with no moving branches etc. in the field
view.
- Ensure detector is not being activated by stray moving heat sources such as heating outlets, car etc.
5. Detector goes on under windy and rainy condition
- Adverse weather conditions and temperature
- This can be minimized by mounting in a protected location.
6. Maintenance and repair
- Do not attempt to repair this unit yourself becausethis can lead to guarantee
invalidity or personal injury.
- Clean detector lens and outside casing with damp cloth.
board before beginning with the electrical wiring.
(BROWN) L
o
(BLUE) N
• 2 x H05RR-F 3C/2C 1.5mm2 max.
field of view is achieved.
changes can result in unwanted activations.
URMET
GrotheGmbH• Löhestr.22• D-53773Hennef•Tel: +49(0) 22 42 - 88 90 - O• Fax: (0) 22 42 - 88 90 - 36 • info@grothe de •
Specifications:
1 . Power: 220-240V
2. Lighting: RL300FV: 2 HI-POWER LEDs
3. Range of detection: Adjustable freom 6m to 12m
4. Angle of detection: 2400
5. Timer: Adjustable from 3 sec.To 15 min.
6. Lux control: Adjustable „Light Level" sensing from
AC 220-240V
5 Lux to 1000 Lux.
7. Protection class
Adjustments:
1. TIME: (O)The motion sensor light has an adjustable TIME control from 3 sec. 15 sec. 30 sec. 1 min. 3 min. 5 min.
10 min. to 15 min. Timer starts working after the last detected movement. While there is movement in the
detection area, the lighting will remain on and the time will keep resetting (Figure B).
2. SENS:
Field of view:
The sensor has a range of detection of 12m at 200C,adjustable from 6m to 12m (Figure C).The sensor head can be
rotated left and right 900 horizontally. The angle of detection
Pleaserefer to figure below (Figure A).
3. LUX: The adjustment controls the sensitivity to the background light level at which the unit will operate
automatically. It may be set to any level between 5 Lux and full daylight. The unit will operate when it senses
movement and the ambient light is at or below the set level (Figure D).
Test: If the arrow is pointing to„TEST".
The light value is deactivated.
When the detector is activated by movement,
the red LED and the lighting remain ON for 3 sec.
4. Blanking inserts:
A. Undesired areas and interference sources can be blanked out of the dtecting range by fitting the supplied
blanking inserts.
B. Trim blanking inserts with scissors either hotizontally
Install the blanking inserts by pushing it into slot around the sensor head. The position can be adjusted by sliding
C.
it around the slot. Please refer to figures below.
RL300FV
PIR MOTION SENSOR
GROUP
/ 50Hz
o
II
is 2400. The recommended
Ideal height 2-3m
12 mm
20 M
5
TIME
Figure. B
or vertically until the desired result is obtained.
LED LIGHT
grothe.de
O
RL300FV
installation height is 2.2m.
Figure. A
9 12
SENS
LUX
Figure. C Figure. D