Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Typ 84476-B
Basic function
• The radio-operated remote control unit
(transmitters) or gateway app controls power
sockets (receivers) selectively and in groups.
• Direct line-of-sight connection between
transmitters and receivers is not necessary (radio
signal).
Positioning
• Do not locate receivers in the corners of rooms.
• Minimum distance between receivers: 1.00m.
• Avoid thick reinforced concrete walls.
Safety
• Read these instructions carefully before starting
use.
• Check all components for any signs of damage.
• If any damage is found, don't connect the product
to the power supply and don't use it.
• Don't open the housing.
• Don't attempt to make any repairs yourself.
• Use the components only in the conditions
described in the technical data.
• Take great care when allowing children to use
them.
• This appliance is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have
been given supervision or Instruction
concerning use of the appliance by a person
responsible for their safety.
• Don´t connect the product to the power supply in
case of any damage.
• Only operate in dry rooms.
• For switch box and cavity wall assembly.
• The device must be disconnected from the main
supply before changing the setting of the
applience, servicing or maintenance.
• Keep assembly and user manual.
• Not intended for use by children.
• Connection only by authorized specialists.
• The device must be enclosure by 2mm thick
insulated cover, min. 4.5mm clearance between
the device and insulated cover.
• Do not mount on electric conductive materials
surface.
• Use only with appliances which are suitable for
uncontrolled use and are not dangerous when
swichting on accidentally
Startup
1. Detach cover and unscrew frame.
2. Connect receiver according to connection
drawing.
3. Fasten receiver to switch box with two
box-screws.
4. Mount frame and cover again.
To set-up article 0086160103, a iComfort rocker set
with suitable frame is needed.
Teaching
• All receivers must be programmed onto the
button to which it is meant to react.
1. The programming mode is activated for about
1 minute by pushing the „LEARN" button of
the product for about 2 seconds. Thereby the
red LED is flashing with a frequency of 1Hz.
2. Now the device must be chosen on the
remote control and transmitted to the receiver by
pushing the „ON" button or operation the rocker
switch.
Group membership
Decide wheter the switch power socket is to react
to a group call (device group 0). (See switch on the
backside)
Only in combination with remote control type 84471-
B.
ON
Must react
OFF
Must not react
Switching without remote control
At the receiver
• open/close shutter: press rocker
• stop shutter: press rocker button again
Technical data
• Range: 100m (free field)
• Supply voltage: 230V~, 50Hz
• Power: 500W
• Inductive load: 500VA (cos(phi)=0,8)
• Fuse: T6,3A H 250V~
• Frequency: 868MHz
• Own power consumption: <0.5 Watt
• Number of device groups: 1
• Number of devices per device group: 10
• Pollution degree: IP20
• Ambient temperature: T25°C
CE Declaration of Conformity
REV Ritter hereby declares that the 84479-B
model is in accordance with the underlying
requirements and other relevant provisions
of Directive 1999/5/EC. For the complete
CE Declaration of
Conformity please refer to www.rev.biz
under the article in question. This product
is a radio controlled system and should
only be used as this. The buttons of the
remote control could not be used permanently.
WEEE-reference of disposal
In accordance with European defaults used
electrical and electronics devices may no
more be given to the unsorted waste. The
symbol of the waste bin on wheels refers
to the necessity of separate collection.
Please help with environmental protection
and see to it that this device is given to the
for this purpose designated systems of waste sorting
if you do not use it any longer.
GUIDELINE 2002/96/EG of the EUROPEAN
PARLIAMENT AND the COUNCIL of January 27th
2003 about electrical and electronics old devices.
Warranty
During manufacturing this REV product is passed
through several quality testing stations which are set
up with newest technology. Should nevertheless a
defect arise, REV offers a warranty to the following
extent:
1. The duration of the warranty is 24 months after the
date of purchase.
2. The unit is either repaired or replaced by REV free
of charge or if it can be shown that it has become
unusable during the warranty period due to a
manufacturing or material defect.
3. The liability does not cover transport damages or
damaged incurred through defective installation.
4. If REV repudiates the warranty claim and no
objection is made within 6 months, the right to
repair becomes time-barred.
5. In a warranty case the unit must be sent to the
dealer or REV together with the sales slip and a
short description of the defect.
6. If there is no proof for a warranty liability being in
place, any repair carried out will be invoiced.
868MHz
REV Ritter GmbH • Frankenstr. 1-4 • D-63776 Mömbris
Tel. +49 900 117 1070 • E-Mail: service@rev.biz • www.rev.biz
Werbung
