8BITDO M30 2.4G Mini Kurzanleitung

8BitD0
M30 2.4G mini
power LED start status
LIZ RIC
x
D-pad c
star home
- select / mode
• press the Start button to turn on the controller
• Hold the Start button for 3 seconds to turn off the controller
• Hold the Start button for 8 secondsto force the controller off
MD mini / MD mini 2 / Genesis mini
Wireless Connection
1.Connect the 2.4Greceiver to the USBport ofyour MDmini / MDmini 2 / Genesis mini console
2. Press the Start button and wait until the controller is recognized by the system to play
Switch
• Switch system version needs to be 3.0.0 or above
• Please ensure the [Pro Controller Wired Communication] is enabled in the system setting
Wireless Connection
1.Connect the 2.46 receiver to the USBport of your Switch
2. Press the Start button and wait until the controller is recognized by the system to play
Wired Connection
1.Connectthe controllerto the Switchvia a USB cable andwait until the controller is recognizedbythe
system to play
Windows
• Windows 10 (1903) or above is required for your Windows device
Wired Connection
1.Connect the controller to the USBport of your Windows device and wait until the controller is
recognized bythe system to play
Turbo Function
• The D-pad, Start, Mode and Home buttons are not supported
• Hold the button you would like to set turbo functionality to, then press the Star button to activate/deactivate
its turbo functionality
Battery
Status — LED indicator —
low battery Red LED blinks
battery charging RedLEDstays solid
battery full charged Red LED turns off
• 35 hours of playtime with a 480 mAh built-in lithium battery pack, fully recharge between Ito 2 hours
• The controller will automatically shut down if there is no connection within 1minute after startup or no
activity within 15 minutes after connection
• The controller will not shut down when ift over wired connection
Repair the controller with the receiver
Ifthe controller loses the connection with the receiver or need to pairwith another same model 2.4G receiver,
please follow the instructions below:
• Press the Start button to turn on the controller, hold the mode button for 3 seconds to enter the pairing
mode, the status indicator starts to blink rapidly
Connect the 2.4Greceiver to your device
Both status indicators become solid when the connection is successful
Support
• Please visit support.8bitdo.com for further information additional support
M30 2.4G mini
English
LED + start
LIZ
x
- select/ mode
* start
MD mini / MD mini 2 / Genesis mini
1. 2.4G MD mini / MD mini 2 / Genesis mini
2. start H-E#fi,
Switch
Switch 3.0.0
- - Pro
1. 2.4G Switch USB
2. start
1. USB Switch USB ,
Windows
Windows Windows 10 (1093)
1. USB Windows iQå-É'<JUSB ,
starts mode, home
480mAh 5EädjÄ51-2
' H-ntä 1 15
1. start mode 3
2. USB
* ilifiiä] support.8bitdo.cn
M30 2.4G mini
+ start
RIC
LIZ
c
home
- select / mode
start
* "*7: start
MD mini / MD mini 2 / Genesis mini
USB 1. 2.4G MD mini/MD mini 2/Genesis mini
2. start
Switch
switch 3.0.0
— —Z Switch
2. start
1. USB switch
Windows
Windows
1. use Windows
start. modes home
480mAh
1. start
2. USB
support.8bitdo.com
M30 2.4G mini
RIC
LIZ
x
c
home*5Y
*VI: start*l
• 1171: start-31S
-E: start
MD mini / MD mini 2/ Genesis mini
USB 1. 2.4G +E171S MD mini/MD mini 2/Genesis mini
2. start
Switch
• Switch
roNJ
-
USB ff— 1. Switch
2. start
1. USB
USB
Windows
10(1093) Windows
1. USB Ahg6hOl
USB #AIQ.
,starts mode. home31É
1-2 35
1-2
a OILHOfl
15
•
l. start
mode 3
2. USB +E171S
3.
71±112
support.8bitdo.com
+ start 71
RIC
x
c
home
- select/ mode
8
USB
01010k
- Pro
USB 2.4G +E171S
switch USB 21401
Windows 10(1093) 01'2010-10} W c}.
Windows USB Æ-EOII 21401
XIZlöhXl
3-41*
15 e
+E171S +E171S RIAL-ICY.
CIS mode 3
AAISOI VII euct.
Oil