UNILITE HL-8R Bedienungsanleitung

PRODUCT FEATURES
• High quality 475 Lumen 6500k white SMD LEDs
• 2 x Side SMD LEDs for wide flood lighting
• 250 Lumen SMD LED for long distance spot beam
•
Intelligent sensor mode for hands-free operation
•
Memory function - remembers last mode used
•
Super tough construction with rubberised coating
•
IP65 dust & water resistant / IK07 shock resistant
•
60° Rotational head
•
Adjustable non-slip silicone lined headband
•
Green Flash-to-Solid Green charging indicator
• Fast 1A USB-C charging - 2.5 hours charge time
• 1m USB-C charging cable included
BATTERY - 3.7v 1500mAh Li-polymer Rechargeable Battery
WEIGHT - 111g
DIMENSIONS - Headtorch - H: 47.5 x W: 78.5 x D: 46mm
RECHARGING
1. Only use a USB-C 5V cable (max 1A).
2. Lift the charging port cover on the bottom of the headtorch and
plug the USB-C end of the cable into the charge port.
3. Plug the USB-A end of the cable into a USB charging source (do not
exceed 5V-1A charging input or damage may occur.
use "Fast Chargers" as this can over-load the
4. Green flashing LED indicates charging, solid green LED confirms
fully charged.
5. Charge Time: 2.5 hrs
**Warranty void if not used with the specified chargers**
Charge Port
HEADBAND INSTALLATION
Feed the small buckle through these gaps in the back
Sliding adjuster
buckle
| EU Responsible Contact:
Aspen Pumps France, 353 Allee des Vergers, 76360 Barentin
Tel: +33 (0) 1 78 95 88 82 Email: ventes@aspenpumps.com
English
Please do not
battery).
Detach small buckle from the
looped end of the headband
plate of the headtorch, keeping the silicone facing
you, then re-attach the small buckle back onto the
looped headband.
ANSI FL1 Standard
SPOT BEAM
FLOODLIGHT -
HIGH
FLOODLIGHT -
MEDIUM
FLOODLIGHT -
LOW
OPERATING INSTRUCTIONS
RIGHT SWITCH = MAIN MODES
Switch sequence: Spot Beam > Flood light Low > Flood light Medium >
Flood light High > Off
MEMORY FUNCTION: If left in any mode for over 5 seconds, the next
press will turn off. Next time you turn ON, it will return to the last Mode
used.
LEFT SWITCH = SENSOR MODE
Press the left switch to activate SENSOR mode, a red light will appear
to confirm sensor mode is activated. Then wave your hand in front of
the head lamp to turn it ON or OFF (sensing distance less than10cm).
Sensor mode available in FLOOD LIGHT HIGH and SPOT BEAM modes.
The Memory Function will remember which mode was last used and
the Sensor will turn on these LEDs in High mode. Press SENSOR switch
again to turn SENSOR mode OFF.
On/Off Switch
ADVICE & IMPORTANT INFORMATION!
ƒ Do not look directly at LEDs.
ƒ Do not operate in direct sunlight or extreme temperature conditions (below -10˚C or
above 40˚C).
ƒ LEDs can become warm/hot when switched on; DO NOT touch and NEVER place face
down on any surface – risk of fire!
ƒ Do not use the device if there is any visible damage.
ƒ Do not use the device in the immediate vicinity of flammable materials or gases.
ƒ Take care when charging, check the charging output on the charging source you are
using and DO NOT exceed the stated Max charging input or damage may occur to the
battery and may void the warranty.
ƒ The rechargeable battery will reach full performance after a few complete charging
and discharging cycles.
ƒ To keep the rechargeable battery in optimum condition, it should be recharged every
3-6 months, especially if it is not being used for a long period of time.
ƒ Always fully charge rechargeable batteries before storage.
ƒ Always protect lithium batteries from heat, intense sunlight, fire, water and moisture
– danger of explosion!
ƒ If a battery is damaged, fluids can leak out. AVOID contact as this can lead to skin
irritation and/or burns. If skin contact occurs, rinse thoroughly with water. If irritation
persists, seek medical advice. Seek immediate medical assistance if lithium battery
fluid comes into contact with the eyes.
ƒ Children under 12 years of age should only use the product under adult supervision.
ƒ Do not disassemble or attempt to modify the product; this will void the warranty and
can be dangerous. Improper use or modification is not covered under the warranty.
ƒ Take care not to let lenses come into contact with hard/sharp objects, damage/
scratches to lenses will affect light output.
ƒ Before cleaning the product, disconnect the charge cable. Clean with a dry or slightly
moist, clean, lint-free cloth and a mild detergent if required. Do not use cleaners that
contain abrasives or solvents.
ƒ This product is water resistant to IPX5 – DO NOT SUBMERGE. If the product has been
subjected to excessive moisture/water the warranty may be void.
ƒ This product has a 1 year standard warranty (or extended to 2 years once registered
online at WWW.UNILITE.CO.UK/WARRANTY) against manufacturing faults and
defects. It does not cover normal wear and tear, modifications, accidental damage or
poor maintenance. Unilite warranties do not cover disposable battery leaks or the use
of incorrect chargers and cables that can damage rechargeable batteries.
ƒ Do not dispose of this device in normal household waste. It must be disposed of via
an authorised electrical appliance disposal centre or at your local waste disposal unit.
ƒ Please re-use or recycle packaging responsibly.
ƒ Keep these instructions for future reference or for subsequent possessors.
www.unilite.co.uk
HL-8R
250
90M 6H
Lumen
475
25M 4H
Lumen
250
16M 8H
Lumen
30
6M 35H
Lumen
Sensor Switch
The LAB, Winyates Way, Redditch B98 9FG
Tel: 01527 584344 Email: support@unilite.co.uk
UNILITE |