Lorelli bertoni RIDER Gebrauchsanweisung Seite 6

Battery safety information.
BG - The product needs alkaline batteries (not included in the set). To be assembled by an adult. Battery safety information
ATTENTION! In certain cases from the batteries may leak liquids, which may
cause chemical burning or may damage the product. To prevent leakage from the batteries:
- Do not mix old and new batteries or batteries of a different type.
- Place the batteries as shown inside the batteries compartment.
- If the product will not be used for a longer time, remove the batteries. When batteries are depleted, remove them from the product.
Discard safely the batteries, Do not throw batteries in a fire. Batteries may explode or leak.
- Do not cause a short circuit
- Use only identical batteries or batteries of one type, according to the recommendations.
- Do not recharge batteries, which are not rechargeable.
Batteries contain substances that are harmful to the environment.
waste but deliver them to a specialized place for collecting batteries. Always remove the battery before disposal of the device or
delivering it to an official waste collection point. IMPORTANT!
together with the ordinary household
protection.
Protect the environment by not disposing of this product with household waste
(2012/19/EU).
Check the recommendations
MAINTENANCE AND CARE
Wipe with a clean cloth dampened
bleach. Do not dry clean.
To be sure that your children will not be accidentally injured ,please regularly inspect and take care ofthe walker.
1. The walker is a device that helps children learn how to walk. To prevent incidents, regularly check the product's condition.
2. Check the belts, the bolts, and all parts before use.
3. Check the good working order of the locking mechanism.
4. To take care ofthe health ofyour child, regularly wash and dry the seat.
5. This walker is made of plastic, iron pipes, fabric, and foam rubber. Do not store the walker in wet, cold, or too warm places.
6. Do not overload the walker.
Characteristics
Photo A
I. Front mirror
2. Panel
3. Base
Install the front and the rear wheels on the base at the designated
follows, two on each long side and one on the front part of the base (photo 1). CAUTION:
prevent the falling of the walker
part upwards until you hear "a click" (photo 3 a/b). Unfold the panel with the seat as shown in photo 3 cld until you hear "a
click". Set upright the back of the seat until you hear "a click" (photo 3 d). Install rear mirrors in the assembly holes on both
sides of the panel (photo 4). Install the batteries - this product uses two batteries AA 1,5 V (not included in the set). Remove
the cover of the batteries located behind the music panel by unscrewing the fixing screw. Place the batteries as shown on the
cover and the place for installation
screw. Press the musical buttons on the active panel to reproduce
photo 6 on the panel and put the upholstery on the plastic back.
To set the height of the baby walker, press the three buttons for setting the legs, as shown in photo 7. To
transform the walker into an active walker, press simultaneously the two buttons underneath to connect the panel
and the front part as shown in photo 8, then turn the panel and remove it from the base together with the supporting
legs by using the buttons under the base to detach the left and right leg (photo 9). To remove the rear spoiler, first,
remove the back wheels. At the bottom of the released
pressed, release the rear spoiler. The walker has the function to slow the movement by tightening the screw, which
is located on the side of the two
in the batteries.
waste but deliver it to an official collection point. Thus you will help with environmental
to local authorities about recycling (Only for Europe).
with a mild soap and water solution. Do not immerse. Only surface wash. Do not use
CARE
- 2 pcs.
- 1 pc.
- 1 pc.
downstairs! Assemble the rear spoiler to the base as shown in photo 2. Unfold the front
(watch for the poles "+" and "-i'). Then close the cover of the batteries and fix it with the
rear wheels.
Do not throw the batteries together with the ordinary household
After the end of the service life of the device, do not dispose of it
AND MAINTENANCE
4. Front wheel
5. Seat
6. Rear spoiler
7 Rear wheel
8 Rubber stopper
ASSEMBLY
places and fix them firmly. Install the rubber stoppers as
music (photo 5). Install the seat by the method shown in
OPERATION
holes of the wheels are found the clamps which when
- 2 pcs.
- 1 pc.
- I pc.
- 2 pcs.
- 5 pcs.
Always use the stoppers to