Xtool SafetyPro AP2 Kurzanleitung Seite 11

EN
Thank you for choosing xTool products!
If you use the product for the first time, read carefully all the accompanying materials of the
product to improve your experience with it. If you do not use the product according to the
instructions and requirements of the Manual, or mis-operate the product due to misunderstand-
ing, etc., the Company shall bear no responsibility for any loss resulting therefrom.
The Company has collated the content of the Manual rigorously and carefully, but errors or
omissions may remain.
The Company is committed to continuously improving product functions and service quality, and
therefore reserves the right to change any product or software described in the Manual and the
content of the Manual at any time.
The Manual is intended to help you use the product properly and does not include any description
of hardware and software configuration. For product configuration, refer to the related contract (if
any) and packing list, or consult your distributor. Images in the Manual are for reference only and
the actual product may vary.
Protected by copyright laws and regulations, the Manual shall not be reproduced or transcribed in
any way, or be transmitted on any wired or wireless network in any manner, or be translated into
any language, or be modified in any way, such as content, image, or layout modification, without
the prior written authorization of the Company.
The Company is committed to continuously improving the product and related materials. The
product and the Manual are subject to change, and updates can be found at xtool.com.
Declaration of conformity
Hereby, Makeblock Co., Ltd., declares that this product is in compliance with the essential
requirements and other relevant provisions of Directive RED 2014/53/EU and the RoHS directive
2011/65/EU & (EU) 2015/863.
FCC statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interfer-
ence received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compli-
ance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communica-
tions.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
■ Consult the dealer or an experienced radio/TV technician for help.
FCC radiation exposure statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
cm between the radiator and your body.
01
Statement ISED Statement
This device complies with Innovation, Science and Economic Development Canada License
exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d' Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes :
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
The device is compliance with RF exposure guidelines, users can obtain Canadian information on
RF exposure and compliance. The minimum distance from body to use the device is 20cm.
Le présent appareil est conforme Après examen de ce matériel aux conformité ou aux limites
d'intensité de champ RF, les utilisateurs peuvent sur l'exposition aux radiofréquences et compli-
ance d'acquérir les informations correspondantes. La distance minimale du corps à utiliser le
dispositif est de 20cm.
Safety first (important)
Read the following warnings and suggestions carefully:
■ Do not use the smoke purifier in places where the temperature is high (over 60℃), fire or
explosion is likely to happen, or there is liquid and oil.
■ Ensure that earthing is done before operation.
■ Only professionals can open the rear panel to examine or repair the purifier as the voltage inside
it reaches 310V.
■ Do not move any filter or cyclone during operation.
■ Do not touch the rotating impeller with hands or other objects.
■ To clean or maintain this product, disconnect the power supply first.
■ Ensure that the purifier operates in the specified voltage range (subject to the power informa-
tion labelled on the machine). Turn off the purifier and disconnect it from the power supply when
the voltage is unstable.
■ The operating humidity ranges from 40% to 80%. Do not use the machine out of this humidity
range. Otherwise, the filters may fail to work soon and the interior circuit may be damaged.
■ The filters come with protective packaging. Remove the packaging before use. Filters are
disposable and do not wash and then reuse them. Purchase filters from Makeblock for replace-
ment regularly.
■ Place filters in the purifier before operation. Without filters, smoke or dust particles may enter
the van and control system and thus damage them. When this happens, you have to fix it at your
own expense.
■ Stop using the purifier when filters are heavily blocked. Otherwise, the purifier may become less
durable and even be damaged. Regularly clean and maintain it, and routinely change filters to
ensure the proper operation of the purifier.
■ Ensure that all the filters are set properly before operation. When the filters are blocked, poor at
filtering or fail to work, purchase filters from Makeblock to replace them.
Maximum RF transmit power: Bluetooth (2402–2480 MHz) < 20 dBm
After-sales services
support@xtool.com.
For technical support, contact us at
For more information about after-sales services, visit
support.xtool.com.
EN
02