Important Notice; Technical Data; Warning Notices - Em2Go Take11 Bedienungsanleitung

GB
Thank you for choosing this portable universal electric vehicle
EM2GO
charger from .
With this unit, you have chosen a high-precision charger equipped with many safety-related
protections that will ensure all-around worry-free charging for your vehicle.

Important Notice:

This manual contains important instructions and information to follow during installation, operation
and maintenance. Read all safety information and warnings in this manual to be aware of potential
hazards. Keep this user manual in a safe place.
Warning
When using electrical products, always observe these basic precautions.
The charger is equipped with a Type 2 EV plug, use this only for vehicles with the appropriate
•
IEC 62196-2 EU mating connector (Refer to your vehicle owner's manual).
Do not install or use the charger near explosive, corrosive or fl ammable materials, chemicals
•
or vapors.
When charging is complete, fi rst remove the Type 2 plug from the vehicle, then remove the
•
charger unit from the mains to avoid damage.
Be sure to disconnect the charger from the mains when not in use.
•
Do not use the charger if it is defective or visibly damaged.
•
Do not use the charger when it is covered.
•
Do not attempt to open, disassemble, repair, tamper with, or modify the charger. If you have
•
any questions or need repairs, contact our customer service department.
Do not use the charger with extension cords.
•
Do not use the charger when you are in the vehicle.
•
Do not use the charger when exposed to heavy rain, snow or inclement weather.
•
Always use caution when transporting the charger.
•
Store the charger in the designated device to avoid external damage.
•
Never touch the contact surfaces of the charger and do not insert any objects into the connection
•
surfaces of the charger.
Do not pull the charger cable by force or over sharp objects.
•
Unplugged connectors are not waterproof. Always cover them with the protective caps when not
•
in use.
Do not allow children to play with the packaging materials or the charger.
•

Warning notices

Observe the warnings. Failure to observe these precautions may result in serious injury or death.
Incorrect installation and testing of the charger can possibly lead to damage. No liability will be
•
accepted for any resulting damage.
Ensure that the charging cable is properly positioned during charging and cannot be stepped on,
•
damaged or stressed.
Check the wire diameter according to local electrical requirements.
•
7

Technical Data

Operating voltage: 400V AC ±10%, 50Hz ±2%
•
Operating current: 6, 8, 10, 13, 16 Amp adjustable
•
Output power: 3-phase up to 11kW (@400V 16A)
•
Protection against: Overvoltage, undervoltage, overload, short circuit, overtemperature
•
Safety: RCD type-A + 6mA DC
•
Charging standard: EN62752, EN61851-21-2, EN61000-6-1/3
•
Cable lengths: Charging cable 6 m, supply cable 1.5 m
•
Charging plug: Type 2
•
Mains plug: CEE plug 16A 5-pin
•
Display: OLED display
•
LED indicator: LED
•
Power meter standard: Accumulated power consumption metering
•
Housing: IP66 splash-proof
•
Operating temperature: -25 to + 50 degrees C
•
Dimensions: 129 x 104 x 60 mm (LxWxH)
•
Weight: ??? kg
•
Scope of delivery
EV charger
•
CEE protective contact adapter
•
Wall bracket
•
Cable winding
•
1
Carrying bag
•
Operating instructions
•
Overview
1. Type 2 plug
9
2. LED display
3. Supply cable
4. Delayed charging button
5. Current setting button
6. LED display
7. CEE plug
8
8. Protective cap
9. Charging cable
LED display status
State
Red
6A
Power On 8A
Available 10A
13A
16A
Connected
Flashes
Reserved Flashes
Charging
Finishing
Fault Flashes
GB
3
2
4
5
6
LED Display Status
Green 1 Green 2 Green 3
Current indication
Flashes Flashes
Cycle Light
7
8