BITO SDS-Seie Aufbau- Und Bedienanleitung Seite 6

1. Exclusion of liability / warning notices
Exclusion of liability / warning notices
The present instructions of assembly and use must be
made available to every user before a storage installation
is put into operation.
All instructions given in this document must be followed at
all times.
BITO-Lagertechnik disclaims liability for all damages
arising from non-observance of these instructions of
assembly and use.
DGUV 208-061 Observe the
regulations issued
by your national/
local Occupational
Accident Insurance
Institution(s).
General remark
Risk of slipping and
falling
Hand injuries
Do not climb on
shelving
Revolving parts
Do not move
shelving & racking
when loaded
2. General safety notes
BITO shelving and racking is intended for storing and picking unit
loads such as cartons, bins and containers or individual items.
Carton live storage installations have been designed for manual
loading and retrieval (servicing with lift trucks is not allowed). If
carton live storage levels are integrated into pallet racking, the
pallet racking levels can be serviced with appropriate industrial
trucks.
Unit loads, shelf loads and bay loads must not exceed rated load
capacity limits.
Make sure that loads are evenly distributed since structural
design has been been calculated for uniformly distributed loads.
Any other use or any use exceeding that specifi ed is an
infringement of use for the intended purpose.
Follow the instructions on design & layout, components &
technical equipment, assembly & operation specifi ed in the order
documents.
6
GB
Installations in Germany must comply with the safety
regulations for warehouse equipment and machinery
(Richtlinien für Lagereinrichtungen und -geräte) as specifi ed
by the DGUV regulation 208-061 of the German Statutory
Accident Insurance Association as well as the regulations
set up by the German Occupational Safety and Health Acts
(Arbeitsstättenverordnungen) and the relevant accident
prevention regulations.
Installations outside Germany must comply with the relevant
national/local accident prevention regulations for warehouse
equipment and machinery.
Safety gloves
The present instructions do not apply for shelving and racking
used outdoors or in harsh environments subject to wind, snow
and other mechanical stress factors. Moreover, load capacities
indicated in the present document are not valid for earthquake
hazard zones (structural design does not resist seismic forces).
Safety shoes Inform BITO in writing if your installation is to be set up in an
earthquake hazard area and request adaptation of structural
design parameters to the seismic requirements of your region.
Damaged or deformed racking components must immediately be
replaced.
Protective eyewear
BITO Shelving and racking is not suited for use in environments
with exposure to corrosion, splashing liquids, decomposition,
vibrations, explosions, radiation.
High visibility vest
It is not permitted to use loads or load carriers which due to
their nature are subject to oxidation, rust, decomposition or
which might impair proper functioning of any kind of mechanism.
Storing unpacked foods that are in direct contact with racking
General remark
parts and components is not permitted.
Incoming goods awaiting fi xture and fi tting into BITO storage
facilities must be stored indoors. Outdoor storage of such parts
and components is not permitted.
Hearing protection
3. Assembly instructions
The load carrying capacity of the fl oor must be checked by the
buyer. The fl oor must have a concrete quality of at least C20/25
according to DIN EN 206-1/DIN 1045-2 to allow use of heavy
duty fl oor anchors.
Head protection
Floor fl atness must comply with the tolerances specifi ed in DIN
18202, table 3 and RAL-RG 614, section 3.3.4.2.2:
over a distance of up to 1 metre:
over a distance between 1 - 4 metres:
over a distance between 4 - 15 metres:
over a distance of more than 15 metres:
Assembly must be carried out by competent staff trained and
experienced in working with mechanical storage and handling
equipment; all works must be carried out with appropriate tools
and personal protective equipment.
In order to make work easier, we recommend 3 people to carry
out assembly and installation.
Set up shelving & racking only when empty and in compliance
with the instructions.
4 mm
10 mm
12 mm
15 mm