ProLinx 1810IR Bedienungsanleitung

USB RECHARGEABLE HIGH OUTPUT REMOTE
CONTROL LED TRACK LIGHT WITH
MULTI-DIRECTIONAL MOVEABLE LIGHT HEADS
MODEL NO.: 1810IR
Instruction Manual
Location of Controls:
LIGHT
1. 3 Multi-Directional Moveable Light Heads
2. 3 Hi-Output 1W LEDs
3. ON/OFF Switch/Remote Control Signal Receiver
4. Main Power Switch
5. Micro USB Port
6. LED Indicator Light
7. 2 Magnets*
8. Built-In Rechargeable Battery
*Back of light
9. 2 3M Adhesive Pads
10. 2 Metal Plates
11. Micro USB Cable
REMOTE
12. Remote Control Signal Transmitter
13. Power Buttons
14. Dimmer
15. Preset Dimmer
16. Timer
17. Remote Battery Compartment
Mounting Instructions
Mounting - 2 magnets, 2 metal plates, 2 3M adhesive pads & 2 screws included.
Check the location of where you want to place the light. Make sure it is clean and there is no debris or dust.
Option 1 – Magnetic Mounting
Double-sided adhesive pads and metal mounting plates required (included).
Remove protective cover from one side of the double-sided adhesive pad. Place in center of the metal
mounting plate. Do this for both metal mounting plates. Place the metal mounting plate with adhesive
pad onto the magnets located on the back side of the mounting bracket. Adhesive side placed away
from the product (so it can stick into mounting position). Do this for both metal mounting plates. Remove
second protective cover from adhesive tape and place against desired surface. The metal mounting
plate should be adhered to the desired surface. Pulling on the light should disconnect the metal
mounting plate from the magnets. This is permanent tape that may cause damage if removed. Not
recommended for use on wallpaper or delicate surfaces.
Method 2 - Screw Mounting (Optional)
2. Place the screws (included) in pre-drilled holes.
Do not tighten the screws all the way. Leave ½"of
the screws out of the hole.
3. Slide the light to the left or the right so that the necks
of screws are in the narrow parts of the keyhole slots.
Tighten screws until the light is secure to surface.
Do not over-tighten.
Operating Directions
Light Positioning
The unique light heads are fully adjustable. They can slide left and right, rotate 310° left or right as
well as pivot 180° up and down to direct light where you need it.
NOTE : To prevent damage to the unit, do NOT overturn the light heads and only slide light heads while
the light is OFF. Doing so may damage the unit.
YOU CAN OPERATE AND CONTROL THE LIGHT TWO WAYS:
***Main Power Switch: PUSH THE MAIN POWER SWITCH TO ON BEFORE USE. Push the main
power switch to OFF if the light will not be used for a long period of time.***
Manual Operation Using ON/OFF Switch On Light
˙1st press to turn warm white light ON.
˙Press again to turn the light OFF.
Remote Control Operation : REMOVE PLASTIC TAB FROM REMOTE PRIOR TO USE
The remote control will operate the lights within 20 feet. The remote uses Infra Red technology. It is best
to point the remote control at the Infrared Receiver on lights. Physical objects between the remote and
the lights may interfere with the Infra Red signal. Up to 10 lights can be controlled by one remote control.
Power Buttons:
Red - Turns lights OFF
Green - Turns lights ON
Dimmer Buttons:
When lights are ON:
Hold - to decrease brightness
Hold + to increase brightness
Preset Dimmer Buttons:
When lights are ON press 50% or 100%
NOTE : Remote has memory feature. Lights will default to last brightness setting if lights were
turned off & on by remote.
Timer:
When lights are ON press desired timer option (15, 30, 60 or 120 minutes). Lights will flash to confirm
setting.Reset timer by turning lights OFF.
Replacing the Remote Control Battery
CAUTION:This product contains a Button Cell battery. If swallowed, it could cause severe injury
or death in just 2 hours. Seek medical attention immediately.
If the Remote Control does not work to turn the LED light ON, this may be an indication that the battery
needs to be replaced.
1. Slide battery drawer out.
2. Remove battery.
3. Place a new CR2025 button cell battery in position aligning polarity (+) (-) as indicated.
4. Slide battery drawer in.
Built-In Lithium polymer rechargeable battery
* The light is powered by 3.7V 10000 mah internal Lithium polymer rechargeable battery.
* If LEDs appear to be dim, this is an indication that you may need to recharge the battery.
* Full charging time is approximately 6-7 hours.
* You can use your computer, power bank or any USB outlets to recharge the light. Plug one end of the
USB cable (included) into the direct power port on the light. Plug the other end into any USB port on your
computer or other UL Certified Safety Charger with DC 5V 2A or above output & built-in protection
circuitry to protect against short circuit, over-current, over-voltage, over-heating and over-charging. The
power indicator light will illuminate red when the USB cord is plugged in. The power indicator light will
flash after the battery has been charged for 95%. The power indicator light will auto off once the battery
has been fully charged.
NOTE : Please do not try to remove/replace internal Lithium polymer rechargeable battery as it is danger.
Specifications of 1810IR
Lumens: 240LM Wattage: 3W
Run Time:25Hours Lifespan: 30000 Hours
Color Temperature: 4000K Warm White Voltage and Battery of Light: 3.7V 10000 mah Lithium Battery
MADE IN CHINA