Herunterladen Diese Seite drucken

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Scope of Delivery
16 aluminum frame rods with connecting pins
4 aluminum frame rods without connecting pins
4 corner joints
2 fasteners for grip heads
2 tensioning lines
72 BUNGEE-SNAKES to secure the fabric
Assembly
1. For each side of the frame, put together four frame rods with connecting pins and, at the end
of the side, one rod without connecting pin.
2. Slide one grip head fastener each onto two of the resulting frame sides. Place the fastener
precisely in the middle of the frame side and tighten the fixing screws.
3. Put a corner joint on each end of the remaining two frame sides and tighten the fixing screws.
Now put together all four sides of the frame and tighten the remaining fixing screws.
4. - 5. Hook one end of the tensioning line in the hole in the center of the corner joint, then pass
the line over the small wheel on the grip head fastener. Hook the other end of the tensioning line
in the hole in the opposite corner joint. Then use the tensioner to tighten the line. Repeat the
procedure on the other side of the frame.
6. You will need two sturdy tripods with grip heads to set up the frame. The tripods should
always be weighted down with sandbags. Pick up the frame and insert the fasteners in the grip
heads on the tripods, then securely tighten the grip heads.
7. The respective screens are fastened loosely to the frame with BUNGEE-SNAKES and then
adjusted until the fabric is free of wrinkles. Two BUNGEE-SNAKES per corner.
Safety Notes
Please read this warning before the first use.
- Never remove the warning label from the butterfly screens.
- Reflectors and diffusers behave like large sails.
- Wind can easily turn this product into a dangerous instrument.
- Never leave reflectors and diffusers unattended.
- Always secure them with sandbags or in another reliable way to prevent uncontrolled motion
that could harm persons, animals and/or objects.
- Stay far enough away from hot objects such as spotlights or fire.
SUNBOUNCE GmbH · Buchenring 8 - 10 · 21272 Egestorf · Germany
Telefon: +49 (0) 4175 - 80 88 79 87 · Telefax: +49 (0) 4175 - 80 88 79 67
E-Mail: info@sunbounce.com · Internet: www.sunbounce.com
Stand 2012/05/10
© 2013 SUNBOUNCE GmbH. All rights reserved.
Aufbauanleitung
Assembly Instructions
SUN-SCRIM 20x20
Bitte beachten Sie unbedingt diese Bedienungsanleitung vor dem ersten Einsatz des SUN-SCRIM 20x20.
Please read these instructions carefully before using the
SUNBOUNCE.COM
SUN-SCRIM 20x20
for the first time.

Werbung

loading

Inhaltszusammenfassung für SUNBOUNCE SUN-SCRIM-20x20

  • Seite 1 - Stay far enough away from hot objects such as spotlights or fire. SUNBOUNCE GmbH · Buchenring 8 - 10 · 21272 Egestorf · Germany Telefon: +49 (0) 4175 - 80 88 79 87 · Telefax: +49 (0) 4175 - 80 88 79 67 E-Mail: info@sunbounce.com ·...
  • Seite 2 Lieferumfang 16 Rahmenelemente aus Aluminium mit Verbindungszapfen 4 Rahmenelemente aus Aluminium ohne Verbindungszapfen 4 Eckverbindungen 2 Befestigungselemente für Grip Heads 2 Spannseile 72 BUNGEE-SNAKES zur Befestigung der Tücher Aufbau 1. Stecken Sie für jede Seite des Rahmens 4 Rahmenelemente mit Verbindungszapfen und zum Abschluß...