Safety Information - Fontastic Icona Bedienungsanleitung

NOTE: The touch control panel is activated by briefly touching
Music playback
Music playback via Bluetooth@
A Bluetooth@ source must be paired with ICONA to output music!
Start or stop the music playback by briefly touching the start/stop sensor.
Note: The device must support A2DP and AVRCP profile
Music control
To play or stop music, briefly touch the play/pause sensor.
To skip to the next track, touch the volume + sensor for about 3 seconds.
To skip to the previous track, touch the volume - sensor for about 3 seconds.
Volume adjustment
Increase volume: Tap the volume + sensor with a short interruption
Decrease volume: Tap thevolume - sensor with a short interruption
Light control
1.Turn onloff- Touch any point on the light control area (12) for 4 seconds.
2. Brightness - Swipe left/right on the light control area to adjust the brightness.
3. Color temperature - Tap on the light control area to switch between 2700K (warm white) / 6000K (daylight)
color temperature.
Inductive charging
Wireless charging capable devices can be charged via the inductive charging function of the ICONA.
ICONA must be connected to the power grid. If this is the case, place the smartphone
wireless charging area. The charging process starts. The LED lights up blue continuously
off when the smartphone is fully charged. If the LED flashes, there is a malfunction. Please adjust the smartphone on
the charging area. Remove objects between the charging area and the smartphone.
Devices can be charged wirelessly with up to 10 Watts.
NOTE: There must be no metal objects between charging
Sleep mode
Tap the sleep mode sensor to turn sleep mode on or off. The light of the ICONA lamp is dimmed when this function is
activated. The light and speaker will turn off automatically
Digital clock
The digital clock will be set to 00:00 while the power is being supplied for the first time. Once the light is connected
your smartphone, please allow the „Device Notification" on your smartphone.
be synchronized with the time on your phone. The clock display will always stay on even if ICONA is not connected
to your smartphone.
In case of power interruption, the time will be reset, after connecting with smartphone,
taken over by the phone.
Technical Specification:
• BT Version: 5.0
• Profile: AVRCP/A2DP
• Frequency range: 2400-2483 MHz
• Input voltage: 9V DC, 3A
• Charging power wireless: 5W/7.5W/10W
• Loudspeaker: 2 x 5 Watts, 4 Ohm
• Colour temperature: 2700K/6000K
it.
to play and control music over ICONA.
until the desired volume is reached.
until the desired volume is reached.
on the mark in the center of the
during charging and turns
area and the smartphone.
after 30 minutes
The time setting of the digital clock will
the time will be automatically

Safety information:

• Do not open the charger
• Do not expose the device to water and protect it against humidity
• Do not use brute force when connecting
• Disconnect electronic devices from the power when not using them for longer time.
• Do not place cards with magnetic strips, magnetic recording media or metal objects onto the charging area or
between this and your smartphone;
• Remove your smartphones case (if present) before placing it on the charging station.
• Individuals who wear a pacemaker should maintain a sufficient distance between the device and their pacemaker.
in doubt, consult your treating physician.
• This product may interfere with the proper functioning
hospitals and other medical facilities.
• Never use the product if signs of damage are visible.
No liability is accepted for any damage which may occur through improper operation.
If you require technical support, please contact our support team via email at service@fontastic.eu.
Registration and Safety
Certification/General Information
We hereby declare, that this device carries the CE mark in accordance with the regulations and standards.
It conforms with the fundamental
2011/65/EU.
The full text of the EU declaration of conformity is available at the following internet address: www.d-parts.de/Konfo
Note on environmental protection:
After the implementation of the European Directive 2012/19/EU
applies: Electrical and electronic devices may not be disposed of with domestic waste. Consumers
obliged by law to return electrical and electronic devices at the end of their service lives to the public
collecting points set up for this purpose or point of sale. Details of this are defined by the national law of the
respective country. This symbol on the product, the instruction manual or the package indicates that a product is
subject to these regulations. By recycling, re-using the materials or other forms of utilising old devices, you are
making an important contribution to protecting our environment.
to
the adapter.
no charging will take place and can lead to overheating!
of medical equipment. Consequently,
requirements of the RED 2014/53/EU, as well as the RoHS directive
in the national legal system, the following
If
do not use device in
are