LIVARNO home HG01767A Montage-Und Sicherheitshinweise Seite 8

CAUTION! DANGER OF TIPPING
m
OVER! Ensure that the product stands in stable
equilibrium on a firm surface. The hanging
umbrella must always be used in conjunction with
4 pieces of approx. 50 x 50 x 5 cm paving slabs
with minimum total weight 90 kg (not included).
Otherwise the hanging umbrella could tip over
and result in injury and damage to property.
Never move the hanging umbrella in the open
state. Always fully close the umbrella top
and pull in the arm
load on the product could become unbalanced
and cause it to overturn, resulting in injury
and / or damage.
CAUTION! FIRE HAZARD! Never place
the product near an open fire and / or radiant
heaters.
Make sure that this product is standing on a solid,
level surface.
Make sure the product is stable before use!
m CAUTION! RISK OF INJURY! Before
opening and closing the product, make sure that
there are no people standing too near to it.
CAUTION! RISK OF CRUSHING! Watch
m
your fingers when opening and closing the
product. If you are careless, you risk injuring your
fingers by crushing them!
Ensure that the top pole with attachments
attached firmly to the lower pole section
the paving stand. Unless this is done, it is not safe
to use the hanging umbrella.
Close the hanging umbrella if the wind
shows signs of increasing in speed or
on the approach of squally showers.
Never use the product as protection against bad
weather.
Never leave an open hanging umbrella
unattended. Damage could occur if strong winds
arise unexpectedly.
Close the hanging umbrella in the event of wind,
snow or rain.
Do not hang any objects (e.g. clothing) from the
product.
6 GB
[ 8 ]
completely. Otherwise the
7 ] [
6 ] [
3 ] [
˜ Assembly / disassembly
Note: For assembly you will need a working space
at least 16 m in area and 4 m in diameter.
2
Note: If possible have a second person help you
with the assembly.
˜ Assembling the paving stand
Fit the cross member for paving stand 2
top of the cross member for paving stand 1
(Figure B).
first
Bolt the bottom pole section
cross members. Use a wrench to tighten the
bolts with the washers
[ 4 ]
Place the paving slabs (not included) evenly on
the assembled cross members (Figure D).
Note: Keep 4 pieces of approx. 50 x 50 x 5 cm
paving slabs with minimum total weight 90 kg close
at hand for the paving stand.
Insert the top pole section
section (Figure E, step
3 ] [
nut (Figure E, step
[ ]
˜ Opening the umbrella top
Release the handle
a counter-clockwise direction (Figure F, step
Push the handle
stopper (top pole section)
Lock the handle by the locking knob
clockwise direction (Figure F, step
is
Push the crankcase
on
reaches the stopper (arm)
Lock the support rod
sleeve downwards to the holder
[ ]
step ).
2
Open the umbrella top
the crank
[
step ).
1
Note: The umbrella top
opened manually at the beginning. The fabric might
be stuck together.
To prevent issues during windy conditions, tie the
strap with adjustable buckle
section (Figure H, step
9 ] [
Note: Alternatively, insert the strap with adjustable
buckle into the loops
[ ]
to the assembled
3 ] [
(Figure C).
5 ] [
into the bottom pole
[ 9 ]
). Tighten the union
1
).
2
by the locking knob
[ ]
upwards until it reaches the
[ ]
(Figure F, step
[ ]
3
upwards until the arm
[ ]
(Figure G, step
[ ]
by inserting the plastic
[ ]
completely by turning
[ 8 ]
in a clockwise direction (Figure H,
]
might need to be
[ 8 ]
onto to top pole
[ ]
).
2a
(Figure H, step
[ ]
on
[ 2 ]
1 ] [
in
[ ]
).
1
).
2
in a
[ ]
).
7 ] [
).
1
(Figure G,
[ ]
).
2b