Somogyi Elektronic SAL RRT 7 Bedienungsanleitung Seite 5

• The playback of supported files is not always guaranteed, as it may be affected by software and hardware conditions independent of the manufacturer.
• The manufacturer cannot be held responsible for lost or damaged data, etc., even if the data, etc. is lost while using this product. It is recommended to make a
backup copy of the data and programmes on the connected media to your personal computer beforehand.
FM RADIO
Press and hold the M button to switch to FM radio. Press the M button briefly to search for and store radio stations that can be received at the place of use. Then a
short press of the buttons will step through the programmes.
Attention! The charging cable, which also acts as an antenna, must be connected to the radio. Do not plug the other end into the charger, but leave the wire free
and straighten it out.
• Lift the antenna cable of the device and fix it higher. If reception is weak, move the device to another location and retune.
• The search stops when it detects changing signal strength - this does not always mean finding a radio programme. Skip through these blank spaces when listening
to the radio.
• Radio reception depends to a large extent on the geographical location of use and the current reception conditions.
• Do not place large metal objects or electrical equipment near the appliance!
STEREO AUX AUDIO INPUT
By plugging a stereo audio jack cable (with a 3.5 mm plug) into the AUX socket, you can listen to the sound of an external source - if it has an audio output or
headphone jack. You can even connect this speaker to a computer. When the cable is connected, the device automatically switches to this input. A short press of the
M button mutes the device, a long press switches it to another signal source.
• An audio cable with the appropriate plug for the external device you want to connect must be purchased separately.
• This input is stereo. If only one of the speakers is playing, the connection cable is probably not the right one.
CLEANING, MAINTENANCE
Switch off and unplug the charger before cleaning. Do not leave anything connected to it. Use a soft, dry cloth. Use a cloth slightly dampened with water to remove
heavy dirt. Do not get dampness on the connectors and buttons! Do not use aggressive cleaning agents!
Regularly check the integrity of the charging cable and the casing! In case of any abnormality, immediately disconnect the power and contact a professional
TROUBLESHOOTING
If an error is detected, switch off the device and remove any connected devices. Try to switch it back on later. If the problem persists, check the following list. This
guide may help you troubleshoot the problem if the device is otherwise connected as specified. If necessary, consult a professional!
General
The device does not work, the indicator is not lit.
• The device is not switched on.
- Check the status of the on/off switch.
• The built-in battery is dead.
- Connect the charging cable and charge the battery.
The device seems to work, but it does not make a sound.
• The volume control is not set correctly.
- Check that the volume control is not set to minimum.
Not playing files from the correct signal source.
• The wrong signal source or device is selected.
- Press and hold the MODE button repeatedly.
Music playback does not work.
• A typing error has occurred. MP3 format is not compatible.
- Make sure that the MP3 format is correct.
• Contact problem at the USB or memory card socket.
- Check that no foreign objects have been inserted into the socket. If necessary, clean carefully with a brush.
- Contact problems can also be caused by incorrect (e.g. skewed or rough) connections. Reconnect the external unit.
• Faulty or non-compliant external memory device.
- There may also be differences between memory units of the same type that affect usage.
Noisy playback.
• A typing error has occurred. MP3 format is not compatible.
- Make sure that the MP3 format is correct.
• The media is faulty or there is a contact error when connecting.
- Check that the media is correct and connected.
• A data copy error has occurred.
- Check the compression software and computer you are using.
Noisy radio reception.
• Reception conditions are weak.
- Move the device to another position. Lift the antenna cable higher. Then retune the radio stations.
5