bihl+Wiedemann AS-i 3.0 Bedienungsanleitung Seite 4

AS-i 3.0 PCI-Board
5.2 Einbau des AS-i 3.0 PCI-Boards .................................................................... 18
5.2.1 Ausbau des AS-i 3.0 PCI-Boards ................................................................ 18
5.3 Einbau des AS-i 3.0 Compact PCI-Boards .................................................... 19
5.3.1 Ausbau des AS-i 3.0 Compact PCI-Boards ................................................. 19
5.4 Anschluss an einen oder mehrere AS-i-Kreise .............................................. 20
5.5 Installation der Treibersoftware ...................................................................... 20
5.6 Deinstallation der Treibersoftware ................................................................. 20
5.7 Windows-Device-Treiber und DLLs ............................................................... 21
5.8 OPC-Server ................................................................................................... 21
6 Kommunikation über das Dual Port RAM (DPRAM) ..................................... 22
6.1 DPRAM-Adrestabelle ..................................................................................... 22
6.1.1 AS-i-Kreis 1 ................................................................................................. 22
6.1.2 Gerät Teil 1 .................................................................................................. 22
6.1.3 AS-i-Kreis 2 ................................................................................................. 23
6.1.4 Gerät Teil 2 .................................................................................................. 23
6.1.4.1 Analogdaten Kreis 1 ................................................................................ 24
6.1.4.2 Analogdaten Kreis 2 ................................................................................ 24
6.1.4.3 Beispiel: Organisation der Analogdaten in DPRAM ................................. 24
6.2 Elemente des DPRAMs ................................................................................. 24
6.2.1 LAS, LDS, LPS, LPF und LOS .................................................................... 24
6.2.2 IDI, ODI, PI und PP ..................................................................................... 25
6.2.3 Control Flags ............................................................................................... 25
6.2.4 Host Interface Flags .................................................................................... 26
6.2.5 Config OK Delay .......................................................................................... 26
6.3 Watchdog aktivieren ...................................................................................... 26
6.3.1 Interrupt erzeugen ....................................................................................... 27
7 Kommandoschnittestelle ................................................................................ 28
7.1 Layouts der Kommandoschnittstellen ............................................................ 28
7.2 Handshake ..................................................................................................... 28
7.3 Aufbau der Legacy-Kommandoschnittstelle .................................................. 29
7.3.1 Beschreibung der einzelnen Bytes .............................................................. 30
7.3.2 Liste aller Befehle ........................................................................................ 31
7.3.3 Beschreibung der einzelnen Befehle ........................................................... 32
7.3.3.1 Write Output Data Image ODI .................................................................. 32
7.3.3.2 Set Permanent Parameter ....................................................................... 32
7.3.3.3 Get Permanent Parameter PP ................................................................. 33
7.3.3.4 Write Parameter ....................................................................................... 33
7.3.3.5 Store Actual Parameters .......................................................................... 34
7.3.3.6 Set Permanent Configuration PCD .......................................................... 34
7.3.3.7 Get Permanent Configuration PCD ......................................................... 35
7.3.3.8 Store Actual Configuration ....................................................................... 35
7.3.3.9 Read Actual Configuration CDI ................................................................ 36
7.3.3.10 Set List von projektierten Slaves LPS ...................................................... 36
7.3.3.11 Set Operation Mode ................................................................................. 37
7.3.3.12 Change Slave Address ............................................................................ 37
7.3.3.13 Execute Command .................................................................................. 38
7.3.3.14 Read Analog Input Data AIDI .................................................................. 38
Zumutbare Änderungen aufgrund technischer Verbesserungen vorbehalten.
2
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Inhaltsverzeichnis
Copyright Bihl+Wiedemann, Printed in Germany