Stalgast 786010V01 Bedienungsanleitung Seite 12

6.2. Commissioning the device
1. Before using it for the first time, make sure that the voltage of the device is compatible with the voltage available at
the installation site.
2. Make sure that the emergency stop button of the device (Figure 1 item 4) is not pressed. If it is pressed, turn it in the
direction consistent with the arrows on min placed.
3. Turn on the device (Figure 2 item 5).
4. Use the „+" and „-" buttons (Figure 2 item 1) to set the appropriate speed.
5. Use the „+" and „-" buttons (Figure 2 item 4) to set the appropriate operating time.
6. Press the START button (Figure 2 item 6) to start the device.
7. When the countdown of the set time is complete, the device will beep.
CHANGE OF ROTATION SPEED
To change the speed of the device, press the button corresponding to the desired speed (fig.2 item 1) - smooth speed
control.
8. If the operating time has not been set - when the product being prepared has reached the right consistency, turn off
the device using the STOP button (Figure 2 item 8) or the emergency shutdown button (Figure 2 item 5).
9. Lift the cover.
10. Remove the finished product.
6.3. Tips
• Pressing the REVERSE button (Figure 2 item 9) will change the direction of the hook to counterclockwise and the RE-
VERSE light will come on. Pressing the button again will stop the reverse motion.
• Pressing the PAUSE button (fig. 2 item 7) stops the operation of the device for example: to check the consistency of
the product. Pressing the START button (fig. 2 item 6) will continue operation with the set parameters.
• In case of an emergency, you can turn off the device by pressing the emergency shutdown button (fig. 1 item 4)!
• At the maximum load, the device must not operate for more than 20 minutes.
• During the operation of the device, the bowl guard should be closed.
• At maximum loading, the device must not operate for more than 20 minutes.
6.4. Overload protection
Sudden stopping of the device may indicate that it is overloaded. If the device suddenly stops working, turn it off, then
check whether the contents of the bowl are in accordance with the manufacturer's recommendations, make any adjust-
ments to the contents of the bowl. Wait about 20 minutes and turn the mixer on again.
If the device continues to stop or cannot be turned on, contact the service center for further information.
Overloading the device may cause damage. Damage resulting from overloading the device and improper use is not
subject to warranty repair.
7. CLEANING AND MAINTENANCE
After each use of the device, the bowl and the screw mixer should be thoroughly cleaned according to the rules of the
country of use. Before leaving the factory, the mechanisms and bearings of the machine were coated with high-quality
grease to ensure the proper operation of the mixer for 6 months. To ensure reliable operation, the mechanisms and be-
arings should be re-coated with a layer of grease after 6 months. The lubrication process should be carried out by quali-
fied personnel. The device should be thoroughly cleaned after lubrication.
8. DISPOSAL OF THE OLD APPLIANCE
Information for users on the rules concerning proper disposal of electrical and electronic equipment at the end of its life.
• Leave your old equipment in the shop where you purchase a new appliance. Each store is obliged to accept old equip-
ment free of charge if you buy there the new equipment of the same type and in the same quantity. The only condition
is to deliver the old equipment to the store at your expense.
• Dispose of your old equipment at a collection point. Information about the location of the nearest collection point can
be found on the local website or the notice board of the municipal office.
• Leave the equipment at a service point. If the repair of the equipment is unprofitable or impossible for technical re-
asons, the service is obliged to accept this appliance free of charge.
• Return the used equipment at the end of its life without leaving your home. If you do not have the time or ability to
deliver your equipment to the collection point, you can use the services of specialized companies.
Remember! Do not dispose of used equipment together with regular waste. An illegal or incorrect disposal of the pro-
duct will lead to high penalties being imposed.
The symbol of the crossed-out waste bin on the product, its packaging or the instruction manual means that
the product should not be disposed of to normal waste bins. The user is obliged to hand over the used equip-
ment to a designated collection point for proper processing.
9. WARRANTY
The seller shall be liable under the warranty or guarantee.
In case of damage resulting from the formation of lime scale deposits in the device, it is not subject to repair under the
warranty. The warranty does not cover damages caused by external forces such as lightning, changes in supply voltage,
incorrect setting of the voltage value, supply from an inadequate power outlet, mechanical, thermal, chemical damages
to the equipment and the defects caused by them.
Warranty exchange does not cover such elements as: light bulbs, rubber components, heating elements damaged by
lime scale, screws and elements undergoing natural wear, e.g. burners, rubber seals and all kinds of mechanically dama-
ged elements.
- 12 -