Technische Daten - AER acoustiCube 3 Bedienungsanleitung

acoustiCube 3

8. Technische Daten

Channel 1/2
piezo balanced/unbalanced
sensitivity -26dBV, -11dBV with
pad switch on
noise < -82dBV
line/ep unbalanced
sensitivity -28dBV, -13dBV with
pad switch on
Switchable 9V phantom power on
ring ( 2x100mA max)
noise < -80dBV
mic balanced
sensitivity -38dBV
noise < -80dBV
Switchable 48V phantom power
aux in L/R Cinch, unbalanced , 2x560mV
>5 k ž (impedance depending on
"return" setting),
effect 2 return Jack, stereo, unbalanced,
2x 750 mV, >5 k ž (impedance
depending on "return" setting, left
channel on internal speaker
clip indicator Headroom 6 dB
OUTPUT
tuner jack 1.3V, 100 ž
phones jack stereo, max. 1.7 V RMS,
max. 2x 100 mW into 32 ž
For headphones only
Do not connect to other devices
Do not use mono plugs.
di out XLR adjustable 60-240 mV, 100 ž,
balanced, pre/post effect
sub bass jack max. 1.4V (post master),
100 ž, with left channel of effects
Activates 200 Hz active crossover
for built-in speaker
line out jack max. 1.4V (post master),
100 ž, with right channel of effects
L out, R out jack adjustable 0–1.4 V, 100 ž,
stereo effects, balanced
record out channel 1/2
Jack, 1.2V, 100 ž
effect 2 send jack max. 1.2V depending on
"pan" setting, 100 ž
speaker out
subwoofer output jack, max. 120 W into 8 ž
Use only 8 ž passive subwoofer
with built-in 200 Hz crossover
(AER Sub10/200P). Not suitable for
full-range external speaker.
master control 8-pin DIN socket , for Acousticube IIa
footswitch, features:
-14-
Ch. 1/2 volume control / mute
(max –40dB gain reduction)
effects memory 1/2 toggle
effect 1/2 on/off
EQ Channel 1
bass ±10 dB / 60 Hz
middle ±6 dB / 600 Hz
treble ±13 dB / 13 kHz
colour –3 dB bei 100 Hz, +6 dB bei 10 kHz
channel 2
bass ±12 dB / 100 Hz
middle ±12 dB / 1 kHz
treble ±12 dB / 10 kHz
presence filter +0/–16 dB / 10 kHz
notch filter -24 dB at 120 Hz BW-
analog signal processing AER low-distortion limiter,
subsonic filter
built-in effects AER 32-bit digital effects processor,
100 presets
power amp 120 W sine-wave into 8 ž,
discrete bipolar transistor design
limiter threshold 100 W
speaker system 2-way speaker
8" (20 cm) low-midrang
Hexacone driver, Neodym magnet
1" (25 mm) dome tweeter
Neodym magnet
mains power AC 115/230 V (switchable),
50–60 Hz, max. 200 W
mains fuse slow 3.15 A, 5x20 mm
cabinet 15 mm (0.59") birch plywood
Finish waterbased acrylic,
black spatter finish
dimensions 330 x 330 x 265 mm
(13"x13"x10.4") W x H x D
weight 13.00 kg (28,66 lbs)
Notes
Input and output voltages refer to 1 kHz sine-wave test signal.
Input voltages refer to 100 Watts output into 8 ž.
Piezo input sensitivities refer to 500 pF source capacitance and are given
as open-loop source voltages.
Output voltages refer to 50 mV at channel 1, line input. Impedance values
for inputs and outputs are inner impedances (not source or load impedan-
ces - except for power.
Noise measured at line output with
filter 22-22.000Hz, Gain at max. position, pad off, EQ flat, all returns at
min. position, input shorted, Master position refer to 100Watts output
into 8 Ohm ( 1.2V at sub bass )
Specifications and appearance subject to change without notice
= 36 Hz
12 dB
.