Faber KM 90/60 R P Bedienungsanleitung Seite 25

Check engine oil level and top up, if re-
quired
Danger
Risk of burns!
 Allow engine to cool down.
 Wait for at least 5 minutes after switch-
ing off the engine before checking the
engine oil fill level.
 Open the device hood.
 Unscrew and withdraw oil dipstick.
 Wipe off oil dipstick and screw it in.
 Unscrew and withdraw oil dipstick.
 Read the value of the oil level.
– The oil level must lie between "MIN"
and "MAX" marking.
– Add motor oil if the oil level is below the
"MIN" marking.
– Do not fill oil above the "MAX" marking.
 Fill motor oil into the oil fill neck.
Oil grade: see Technical Data
 Reinsert the oil dipstick.
 Wait at least 5 minutes.
 Check engine oil level.
Change the engine oil
Danger
Risk of burns due to hot oil!
 Allow engine to cool down.
 Open the device hood.
 Unscrew and withdraw oil dipstick.
 Draw off engine oil via the oil filler neck
using 6.491-538 oil-change pump.
 Fill motor oil into the oil fill neck.
Oil grade: see Technical Data
 Reinsert the oil dipstick.
 Wait at least 5 minutes.
 Check engine oil level.
Change the air filter
 Remove covering lid.
 Take out the filter inlay.
 Insert a new filter insert.
The filter lamella must point into the di-
rection of the locking cap.
 Attach the locking cap.
All manuals and user guides at all-guides.com
Clean or replace the spark plug
 Remove spark-plug connector.
 Unscrew and clean spark plug.
 Screw in cleaned or new spark plug.
 Push on spark-plug connector.
Empty fuel tank
 Open the device hood.
 Close the fuel supply.
Turn the rotating knob perpendicular to
the fuel tap.
 Open fuel filler cap.
 Draw off fuel using suitable pump.
Check and adjust fill level of hydraulic
oil
 (1) Checking fill level
 Open the device hood.
 Locking screw of the balancing contain-
er.
 Check the fill level in the header tank.
Note: The oil level must be 3 mm above the
container base.
Caution
This inspection may only be carried out
when the engine is cold.
 (2) Adjusting fill level
 Locking screw of the balancing contain-
er.
 If required, top up oil carefully.
 Close container.
Oil grade: see Technical Data
Checking the sweeping mirror of the
side-brushes
 Check tyre pressure.
 The side-brushes lift up.
 Drive sweeper on to a smooth, even
surface covered with a visible layer of
dust or chalk.
 Lower side-brushes and allow them to
briefly rotate.
 The side-brushes lift up.
 Drive machine backwards.
 Park the sweeper on an even surface.
 Check sweeping mirror.
9
-
EN
The width of the sweeping track should lie
between 40-50 mm.
Note:The side brush floating mounting ad-
justs the sweeping track as the bristles
wear down. The side brush must be re-
placed if it becomes too worn.
Replacing side brush
 Park the sweeper on an even surface.
 Set programme switch to step 1 (driv-
ing). Side brushes lift up.
 Turn ignition key to "0" and remove it.
 Loosen 3 fastening screws on the un-
derside.
 Clip side brush on to driver and screw
on.
Checking roller brush
 Park the sweeper on an even surface.
 Set programme switch to step 1 (driv-
ing). Roller brush is raised.
 Turn ignition key to "0" and remove it.
 Secure the machine with wheel
chock(s) to prevent it from rolling away.
 Remove belts or cords from roller
brush.
Replacing roller brush
Replacement is due if a visible deteriora-
tion in sweeping performance caused by
bristle wear is evident.
 Park the sweeper on an even surface.
 Set programme switch to step 1 (driv-
ing). Roller brush is raised.
 Turn ignition key to "0" and remove it.
 Secure the machine with wheel
chock(s) to prevent it from rolling away.
 Raise slightly the waste container on
the left side and pull it out.
 Loosen the fastening screw on the left
side-panel.
 Remove side panel.
25