Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Danger: Water comes out of the coffee nozzle is hot and is collected in the drip
tray underneath. Avoid contact with splashes of water.
♦ After rinsing, the appliance will return to the standby condition.
CLEANING THE APPLIANCE
♦ The appliance must not be immersed in water or any other liquid.
♦ Disconnect the power cord (15) from the main power outlet.
♦ Empty all the water in the internal (3) and external drip tray (1)
♦ Use a damped cloth or non-scratching cleaner to clean the water stains on the
appliance.
IMPORTANT: Never use any abrasive, vinegar or descaling agents not included in
the box to clean the appliance.
PROBLEM
The appliance does not work.
No or delayed response in several trials of pressing
on function key on the panel
The coffee is not hot enough.
The coffee cannot come out from spout.
The first cup of coffee is poor quality.
Coffee has no cream.
The touch buttons are not sensitive
The appliance takes too long time to warm up.
The water tank is removed / the water level is very
low in the water tank but Icon (A) have no alert.
Internal drip tray is filled with a lot of water.
Coffee is delivered too slowly or a drop at a time.
Lack of bean indicator (B) flashes but there is still a
lot of coffee bean inside the container (11).
Milk foam cannot be recreated by steam nozzle
Cleaning coffee powder outlet
♦ Coffee grounds may stick on the wall of ground outlet of appliance, on the way to
Brewing unit (17), after an extended period of use. It is suggested to clean the outlet by
following steps to ensure that coffee grounds can make it to the brewer.
♦ Push the service door recess area (Fig 2)
♦ Take out the service door (Fig 3)
♦ Press the release knob of brewer (Fig 4)
♦ Take the brewing unit out (Fig 5)
♦ Use Cleanness Brush (18) to clean the powder outlet (Fig 12)
ANOMALIES AND REPAIR
♦ Take the appliance to an authorised technical support service if problems arise. Do not
try to dismantle or repair without assistance, as this may be dangerous.
TROUBLESHOOTING
CAUSE
The appliance is not connected to the mains.
Appliance is under an electromagnetic interference
Dirt over the panel
The cups have not been preheated.
The brewing unit is too cold.
Empty system function maybe used before.
The first run of grinder does not pour sufficient quantity coffee
power into the brewing unit.
Coffee bean is not fresh.
Not pressing the touch button from the front direction of the
appliance
Excessive scale has built up.
The area near the water tank connector is wet.
Coffee powder too fine which block the water to come out.
Coffee powder too fine which block the water to come out.
Internal coffee powder outlet is blocked.
The nozzle is dirty and hole on nozzle cover (6) or metal tube
(5) was blocked by milk residual
ENGLISH
(Original instructions)
SOLUTION
Plug in and press the switch.
Check the cable and the Plug
Unplug the appliance. Restart after fewminutes
Clean the panel with the cloth provided
Rinse the appliance at least 3 times before making the
coffee.
Press the hot water button until water can come out from
spout.
Throw the coffee away. The other coffees will always be
of good quality.
Change or using appropriate brand of coffee bean.
Press the lower bottom part of the icon of the touch
button from the front direction of the appliance.
Descale the appliance.
Wipe the water around the water tank connector
Adjust the coffee fineness to bigger dot during grinder
operation.
Adjust the coffee fineness to bigger dot during grinder
operation.
To follow the steps of section (CLEANING COFFEE
POWDER OUTLET).
To follow the steps of section (DAILY CLEANING OF THE
APPLIANCE) to clean steam nozzle
7
Werbung
