Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Safety Information
MI 483 26 Auburn Hills
United States
Mobile: +1 5862020902
Email: tim.copacia@atlascopco.com
The device is only in compliance if no changes or modifica-
tions are made to the device. The antenna is fixed to the de-
vice and no change in antenna or fixation of the antenna is
acceptable and such modification is considered to violate the
Compliance Statement.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pur-
suant to part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the in-
structions, may cause harmful interference to radio com-
munications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the follow-
ing measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is con-
nected.
• Consult the dealer or an experienced radio/TV tech-
nician for help.
ISED Compliance Statement:
This device complies with: CAN ICES-3 (B)/NMB-3(B)
(English) This device complies with Industry Canada's li-
cence-exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including inter-
ference that may cause undesired operation of the device.
(French) Le présent appareil est conforme aux CNR d'Indus-
trie Canada applicables aux appareils radio exempts de li-
cence. L'exploitation est autorisée aux deux conditions suiv-
antes:
1) l'appareil ne doit pas produire de brouillage;
2) l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromet-
tre le fonctionnement.
Information regarding Article 33 in REACH
The European Regulation (EU) No. 1907/2006 on Registra-
tion, Evaluation, Authorization and restriction of Chemicals
(REACH) defines among other things requirements related to
communication in the supply chain. The information require-
ment applies also to products containing so called Substances
4
© Atlas Copco Industrial Technique AB - 9846 0014 00
of Very High Concern (the "Candidate List"). On 27 June
2018 lead metal (CAS nr 7439-92-1) was added to the Candi-
date List.
In accordance with the above this is to inform you that cer-
tain electrical components in the product may contain lead
metal. This is in compliance with current substance restric-
tion legislation and based on legit exemptions in the RoHS
Directive (2011/65/EU). Lead metal will not leak or mutate
from the product during normal use and the concentration of
lead metal in the complete product is well below the applica-
ble threshold limit. Please consider local requirements on the
disposal of lead at product end of life.
Regional Requirements
WARNING
This product can expose you to chemicals including
lead, which is known to the State of California to cause
cancer and birth defects or other reproductive harm. For
more information go to
https://www.p65warnings.ca.gov/
Safety
DO NOT DISCARD - GIVE TO USER
WARNING Read all safety warnings, instructions, il-
lustrations and specifications provided with this
power tool.
Failure to follow all instructions listed below may result
in electric shock, fire, and/or serious injury.
Save all warnings and instructions for future refer-
ence.
WARNING All locally legislated safety rules regard-
ing installation, operation and maintenance shall be
respected at all times.
Statement of Use
• For professional use only.
• This product and its accessories must not be modified in
any way.
• Do not use this product if it has been damaged.
• If the product data or hazard warning signs on the prod-
uct cease to be legible or become detached, replace with-
out delay.
• The product must only be installed, operated and ser-
viced by qualified personnel in an industrial environ-
ment.
ILM Tag
Werbung
