Seite 1
EN — NL — DE kms.vankronenburg.nl Pressure sensor 250 kPa Manual for installation, setup and calibration Handleiding voor installatie, instelling en kalibratie Anleitung für Installation, Setup und Kalibrierung...
Seite 3
EN — NL — DE kms.vankronenburg.nl Pressure sensor 250 kPa Part nr: 01-01-07-2512 Technical specifications and calibration values...
Seite 4
EN — NL — DE kms.vankronenburg.nl This document contains detailed information about the technical specifications and calibration values for the KMS pressure sensor 250 kPa. Additional information, user manuals, wiring examples ands software can be found on our website: kms.vankronenburg.nl Package contents •...
Seite 5
At 3.75 volt: 197 kPa • At 1.25 volt: 72 kPa When using a KMS ECU, these values must be set in the KMS ECU software. See figure below for an example: Engine-load 2’ values for software setup • Min. value: •...
Seite 6
Upper Limit at Uv = 5 V Volt 4.476 4.606 4.736 Response time 10/90 Warm up time - -40 Deg. C 0 to 85 Operating temperature Pressure Min. Value Max. Value (kPa) 0-250 0-200 0-150 0-100 __________________________________________________________ KMS pressure sensor 250 kPa -01-07-2512 Version 2.00...
Seite 7
EN — NL — DE kms.vankronenburg.nl Alternative pressure scales KMS pressure sensor 250 kPa -01-07-2512...
Seite 8
EN — NL — DE kms.vankronenburg.nl Druksensor 250 kPa Onderdeel nr: 01-01-07-2512 Technische specificaties en kalibratie waarden...
Seite 9
EN — NL — DE kms.vankronenburg.nl Dit document bevat gedetailleerde informatie over de KMS druksensor 250 kPa. Overige informatie, handleidingen, kabelboomschema’s en software kan worden gevonden op onze website: kms.vankronenburg.nl Inhoud van de kit • KMS druksensor 250 kPa •...
Seite 10
‘Engine-load 2’ waarden voor software setup • Min. waarde: • Max. waarde: Wanneer er een KMS ECU wordt gebruikt, moeten deze waarden in de KMS ECU software worden ingesteld. Voor gebruik op lagere drukschaal, zie volgende pagina. Zie onderstaande afbeelding ter illustratie: __________________________________________________________ -01-07-2512...
Seite 11
EN — NL — DE kms.vankronenburg.nl Min. Typical Technical data Max. Supply voltage Uv Volt 4.74 5.46 Current input Iv at Uv = 5 V Minimum pressure offset (0 to 85°C) Volt 0.241 0.306 0.371 Accuracy (at 25°C) Volt 0.0701...
Seite 12
EN — NL — DE kms.vankronenburg.nl Alternatieve drukschalen __________________________________________________________ -01-07-2512 Version 2.00...
Seite 13
EN — NL — DE kms.vankronenburg.nl Drucksensor 250 kPa Teilenummer: 01-01-07-2512 Technische Information und Kalibrierungswerte...
Seite 14
EN — NL — DE kms.vankronenburg.nl Dieses Dokument enthält detaillierte Information über den KMS Drucksensor 250 kPa. Weitere Informationen, Bedienungsanleitungen, Schaltpläne finden Sie auf unserer Website: kms.vankronenburg. Inhalt von diesem Kit • KMS Ducksensor 250 kPa • 3-poliger superseal Stecker •...
Seite 15
Bei 3.75 Volt: 197 kPa • Bei 1.25 Volt: 72 kPa Wenn ein KMS ECU verwendet wird, müssen diese Werte in der KMS ECU Software eingestellt werden. Siehe Abbildung unten für ein Beispiel: ‘Engine-load 2’ Werte für der Software Eindstellungen •...
Seite 16
Upper Limit at Uv = 5 V Volt 4.476 4.606 4.736 Response time 10/90 Warm up time Operating temperature Deg. C 0 to 85 Pressure Min. Value Max. Value (kPa) 0-250 0-200 0-150 0-100 __________________________________________________________ KMS Drucksensor 250 kPa Teilenummer: 01-01-07-2512 Version 2.00...
Seite 17
EN — NL — DE kms.vankronenburg.nl Alternative Druckskala __________________________________________________________ KMS Drucksensor 250 kPa Teilenummer: 01-01-07-2512 Version 2.00...
Seite 19
Spaarpot-Oost 19 T +31(0)40 285 4064 5667 KT Geldrop E info@vankronenburg.nl The Netherlands W kms.vankronenburg.nl Please visit our website for more information, manuals, software and prices: kms.vankronenburg.nl...