Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
1. Enter old code + "Status" Key
2. Enter new 4-digit code + "#" key
Enable Arming without Use PIN code
"＊" + "8"
function
Enable Arm with User PIN code function
"＊" + "9"
(Default)
Enable Arming with KP PIN code
"＊" + "0"
function
"Disarm" twice
To leave Test Mode
A
A
r
r
m
m
/
/
H
H
o
o
m
m
e
e
/
/
D
D
i
i
s
s
a
a
r
r
m
m
If Remote Keypad is set to "Arm with Use PIN code" ("＊" + "9"
under Test Mode)
Away Arm
Enter a Control Panel User PIN Code +
"Arm" Key
Home Arm
Enter a Control Panel User PIN Code +
"Home" Key
Enter a Control Panel User PIN Code +
Disarm
"Disarm" Key
If Remote Keypad is set to "Arm without Use PIN code" ("＊" + "8"
under Test Mode)
Press "Arm" Key
Away Arm
Press "Home" Key
Home Arm
Disarm
Enter a Control Panel User PIN Code +
"Disarm" Key
If Remote Keypad is set to "Arm with Keypad PIN code" ("＊" +
"0" under Test Mode)
Enter Keypad PIN Code + "Arm" Key
Away Arm
Enter Keypad PIN Code + "Home" Key
Home Arm
Enter Keypad PIN Code + "Disarm" Key
Disarm
C
h
e
c
k
i
n
g
C
o
n
t
r
o
l
P
a
n
e
l
C
h
e
c
k
i
n
g
C
o
n
t
r
o
l
P
a
n
e
Press the Status key to inquire Control Panel status, the Status
LED will light up according to Control Panel mode
Red LED On
Away Arm mode
Red LED Flash
Home Arm mode
Blue LED on
Disarm mode
D
D
u
u
a
a
l
l
K
K
e
e
y
y
A
A
l
l
a
a
r
r
m
m
F
F
u
u
n
n
c
c
t
t
i
i
o
o
Dual Key Alarm function will activate alarm when both keys are
pressed at the same time. To use the functions, please enable
them under Test Mode. (Default are disabled)
"1" + "3"
Panic Alarm
"4" + "6"
Fire Alarm
"7" + "9"
Emergency Alarm
L
E
D
I
n
d
i
c
a
t
o
r
s
L
E
D
I
n
d
i
c
a
t
o
r
s
A
A
c
c
t
t
i
i
v
v
e
e
L
L
E
E
D
D
The Active LED light up whenever any key is pressed.
Off
Keypad in Standby Mode
Blue LED On
Keypad in Normal Operation
Blue LED Flash
Keypad in Normal Operation and under
Low Battery
Orange LED On
Keypad in Test Mode
Orange LED Flash Keypad in Test Mode and under Low
Battery
S
t
a
t
u
s
L
E
D
S
t
a
t
u
s
L
E
D
The Status LED light up during operation or when the "Status" key
is pressed to inquire Control Panel status
Red LED On
Away Arm mode
Red LED Flash
Home Arm mode
Blue LED On
Disarm mode
Blue LED Flash
No reply from Control Panel
Incorrect PIN code
Request for Home arm when under Away
arm mode
Request for Force Arm
S
t
a
t
u
s
l
S
t
a
t
u
s
n
n
F
a
u
l
t
L
E
D
F
a
u
l
t
L
E
D
The Fault LED light up whenever faults are detected in the alarm
system.
Orange LED On
Alarm in memory
Orange LED Off
Fault exists in system
B
a
t
t
e
r
y
B
a
t
t
e
r
y
The Remote Keypad uses one 3V lithium battery as its power
source. It also features low battery detection function to notify the
Control Panel when battery voltage is low.
When the Remote Keypad is on low battery, follow the procedure
below to change the batteries.
1. Open the back cover.
2. Remove the old batteries.
3. Press any key several times to fully discharge.
4. Insert the new batteries observing correct polarity.
5. Replace the back cover.
F
F
a
a
c
c
t
t
o
o
r
r
y
y
R
R
e
e
s
s
e
e
t
t
If you forget your Keypad PIN code, or the Remote Keypad has
any problem, you can reset the Remote Keypad to factory
default.
1. Open the back cover.
2. Open the back cover and remove the battery.
3. Press and hold "3" key and insert battery.
4. The Remote Keypad will sound 3 short beeps.
5. Release "3" key, the reset process is now complete
S
p
e
c
i
f
i
S
p
e
c
i
f
i
E
n
v
i
r
o
n
m
e
n
t
a
l
C
o
n
d
i
t
i
o
E
n
v
i
r
o
n
m
e
n
t
a
l
C
o
n
d
i
t
i
o
-10°C to 40°C, relative humidity 85% non-condensing.
R
a
d
i
o
R
a
d
i
o
868 MHz
NOTE: This device works with a genuine Rolling
Code encryption. Please only use it with a
control panel with Rolling Code, otherwise
won't be possible to pair the device.
c
a
t
i
o
n
c
a
t
i
o
n
n
n
Werbung
Inhaltsverzeichnis
