Technical Data; Eu Declaration Of Conformity - Atlas Copco ILT Tag ITB-P Sicherheitshinweise

ILT Tag ITB-P

Technical Data

Specifications
Specification
Frequency range, UWB
Transmitting power, UWB
Maximum Radio Output Power
Frequency Range
Radio Technology (MHz)
UWB 5500-7500
Declarations

EU DECLARATION OF CONFORMITY

We, Atlas Copco Industrial Technique AB, SE-105 23
STOCKHOLM SWEDEN, declare under our sole responsi-
bility that the product (with name, type and serial number,
see front page) is in conformity with the following Direc-
tive(s):
2011/65/EU (RoHS),2015/863/EU (RoHS amendment),
2014/53/EU (RED)
Harmonized standards applied:
EN 301 489-33 V2.2.0, EN 301489-1 V2.2.0, EN 302 065-2
V2.1.1, EN 62368-1:2014
Authorities can request relevant technical information from:
Aleksandra Duric, Product Compliance Manager, Atlas
Copco Industrial Technique AB, SE-105 23 Stockholm Swe-
den
Stockholm, 2 May 2022
Carl von Schantz, Managing Director
Signature of issuer
WEEE
Information concerning Waste of Electrical and Electronic
Equipment (WEEE):
This product and its information, meets the requirements of
the WEEE directive/regulations (2012/19/EU), and must be
handled in compliance with the directive/regulations.
The product is marked with the following symbol:
5500 MHz - 7500 MHz
-10.21 dBm
Maximum Trans-
mit Power EIRP
(dBm)
-10.21
© Atlas Copco Industrial Technique AB - 9846 0188 00
Products marked with a crossed-out wheeled bin symbol and
a single black bar underneath, contain parts that must be han-
dled in compliance with the WEEE directive/regulations. The
entire product, or the WEEE parts, can be sent to your "Cus-
tomer Center" for handling.
FCC and ISED Compliance Statement
This device complies with part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This de-
vice may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
FCC Responsible party:
Name: Tim Copacia
Position: Product Manager
Address: 3301 Cross Creek Parkway
MI 483 26 Auburn Hills
United States
Mobile: +1 5862020902
Email: tim.copacia@atlascopco.com
The device is only in compliance if no changes or modifica-
tions are made to the device. The antenna is fixed to the de-
vice and no change in antenna or fixation of the antenna is
acceptable and such modification is considered to violate the
Compliance Statement.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pur-
suant to part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the in-
structions, may cause harmful interference to radio com-
munications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the follow-
ing measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is con-
nected.
• Consult the dealer or an experienced radio/TV tech-
nician for help.
ISED Compliance Statement:
This device complies with: CAN ICES-3 (B)/NMB-3(B)
(English) This device complies with Industry Canada's li-
cence-exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
Safety Information
3