axing premium-line SES 5532-19 Schnellstartanleitung Seite 4

Field of application:
SES 5532-19: Programmable Unicable II multiswitch
The devices are only suitable for distributing radio and television signals inside
the house! If a device is used for other purposes, no warranty is given.
Scope of delivery:
1 × programmable Unicable II multiswitch SES 5532-19
5 × CFA 11-00 terminating resistors
1 × power supply TZU 11-03 | 1 × power inserter TZU 15-04
1 × quick start guide
Note:
You can call up the detailed operation instructions for download by entering
the article in the search field at www.axing.com.
Optionally available:
Programmer SZU 55-00
Combiner SZU 55-02
Preset user bands:
UB1: 1280 MHz (EN50494+EN50607, PIN=1)
UB2: 1382 MHz (EN50494+EN50607, PIN=2)
UB3: 1484 MHz (EN50494+EN50607, PIN=3)
UB4: 1586 MHz (EN50494+EN50607, PIN=4)
UB5: 1688 MHz (EN50494+EN50607, PIN=5)
UB6: 1790 MHz (EN50494+EN50607, PIN=6)
UB7: 1892 MHz (EN50494+EN50607, PIN=7)
UB8: 1994 MHz (EN50494+EN50607, PIN=8)
UB9: 974 MHz (EN50607, PIN=9)
UB10: 1008 MHz (EN50607, PIN=10)
UB11: 1042 MHz (EN50607, PIN=11)
UB12: 1076 MHz (EN50607, PIN=12)
UB13: 1110 MHz (EN50607, PIN=13)
UB14: 1144 MHz (EN50607, PIN=14)
UB15: 1178 MHz (EN50607, PIN=15)
UB16: 1212 MHz (EN50607, PIN=16)
UB17: 1246 MHz (EN50607, PIN=17)
UB18: 1314 MHz (EN50607, PIN=18)
UB19: 1348 MHz (EN50607, PIN=19)
UB20: 1416 MHz (EN50607, PIN=20)
UB21: 1450 MHz (EN50607, PIN=21)
UB22: 1518 MHz (EN50607, PIN=22)
UB23: 1552 MHz (EN50607, PIN=23)
UB24: 1620 MHz (EN50607, PIN=24)
UB25: 1654 MHz (EN50607, PIN=25)
UB26: 1722 MHz (EN50607, PIN=26)
UB27: 1756 MHz (EN50607, PIN=27)
UB28: 1824 MHz (EN50607, PIN=28)
UB29: 1858 MHz (EN50607, PIN=29)
UB30: 1926 MHz (EN50607, PIN=30)
UB31: 1960 MHz (EN50607, PIN=31)
UB32: 2028 MHz (EN50607, PIN=32)
Conditions at delivery:
In the basic setting, the Unicable II output functions in the dynamic mode
(compatible with EN50494/EN50607) and provides 32 user bands. This enables
the connection of up to 32 receivers. Each receiver must be assigned to one of
the 32 user bands.
1 2
3
6
Mounting:
The multiswitch is mounted on a wall or other flame retardant surface.
The multiswitch must under no circumstances be held by the connected cables.
 Use the mounting holes of the SES 5532-19 and use suitable mounting
screws.
Changing the basic settings:
The basic configuration of the multiswitch can be changed by means of the
SZU 55-00 programmer ( available as an accessory). The PC software can be
downloaded at www.axing.com | Downloads.
Connections:
1 Inputs for LNB
V/L, V/H, H/L and H/H for Quattro LNB
V and H left for 1st wideband LNB | V and H right for 2nd wideband LNB
2 Terrestrial input
3 Equipotential bonding connection
4 Unicable II output
5 Legacy/Unicable II output
6 SAT cascade outputs
4
7 TERR cascade output
Power supply:
5
The multiswitch is supplied at the Unicable II output via the power inserter
TZU 15-04 from the power supply TZU 11-03.
7
Equipotential bonding:
To avoid dangerous power surges (e.g. risk of fire and danger of life) the
device must be connected to the equipotential bonding according to
EN 60728-11.
 Use the equipotential bonding connection of the device (3).
 To connect the outer conductor of the coaxial cable to the equipotential
bonding, use e.g. earth connection blocks CFA or earthing angles QEW at
the inputs and outputs of the multiswitch.