axing premium-line SES 5532-19 Schnellstartanleitung Seite 3

Safety advices:
 Installation and repairs to the equipment may only be carried out by
technicians observing the current guidelines. No liability will be assumed
in the case of faulty installation and commissioning.
 Before handling the device, disconnect the power supply, otherwise there
is danger to life. This also applies if you clean the device or work on the
connections.
 Use only the the enclosed power supply unit. Never replace any parts or
make any and the power supply unit. Otherwise, there is a risk of death.
 If a replaceable fuse is available, pull out the mains plug before replacing
the fuse. Replace defective fuses only by standardized fuses with the same
nominal value.
 The equipment may only be operated in dry rooms. In humid rooms or
outdoors there is danger of short-circuit (caution: risk of fire) or
electrocution.
 To prevent damage to your equipment and to avoid possible peripheral
damages, mount the device only on flat surfaces.
 The mains plug is used as a disconnecting device from the mains voltage
both during service and in case of danger and must therefore be reacha-
ble and usable at all times. After connection to the mains, the power
supply is in operation.
 Choose the location of installation or mounting such that children may
not play unsupervised near the equipment and its connections.
 The location of installation or mounting must allow a safe installation of
all cables connected. Connected cables must not be damaged or crushed
by any objects.
 Absolutely avoid that cables come near any source of heat (e.g.
radioators, other electrical devices, chimney, etc.).
 Choose the location of installation or mounting so that under no
circumstances liquids or objects can get into the equipment (e.g.
condensation, water coming from leaking roofs or flowing water, etc.).
 Avoid exposure of the equipment to direct sunlight and to other heat
sources (e. g. radiators. other electrical devices, chimney, etc.).
 Devices that are equipped with heat sinks or ventilation slots must under
no circum-stances be covered or blocked. Also ensure for a generous air
circulation around the equipment. In this way you avoid possible damage
to the equipment as well as a risk of fire caused by overheating.
 In case of damage, interrupt the power supply immediately.
 Do not try to repair the device. This device should only be serviced or
repaired by qualified service personnel. Contact your distributor for more
information.
 Do not open the device.
 For disassembly always pull the mains plug first and disconnect the pow-
er supply cable and the antenna cables from the connected device.
State of the art 2020-06-30
Technical improvements, changes in design, printing- and other errors expected.
Technical data:
Type
Inputs
Number
Frequency range
250...2350 MHz @ SAT
Level (AGC)
Isolation V | H.
Subscriber ports
Number
Supported standards
Tap loss TERR
Frequency range (SAT)
User bands
Gain SAT Unicable II (SCR/CSS)
Gain SAT (Legacy)
Output level SAT (SCR/CSS)
Trunk outputs
Number
Through loss TERR
Through loss SAT
Connectors
Connector type
General
Current consumption
Equipotential bonding connection
Dimensions (W × H × D) appr.
Protection class
External accessories
Switching power supply 100...240 VAC / 50...60 Hz | 19 VDC/940 mA
Power inserter 5...2400 MHz | 18V/750 mA
CE Confirmation Declaration
Hereby, AXING AG declares that the device is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet
address: https://axing.com/en/downloads/ce/.
WEEE Nr. DE26869279 | Electrical and electronic components must not be disposed of
as residual waste, it must be disposed of separately.
Manufacturer EEA contact address
AXING AG Bechler GmbH
Gewerbehaus Moskau Am Rebberg 44
8262 Ramsen 78239 Rielasingen
SES553219
5
5...862 MHz @ TERR
SES 5532-19
59...94 dBµV
>25 dB
premium-line
2
EN 50494, EN 50607
Programmable
13 dB
950...2150 MHz
32
Unicable II Multiswitch
25 dB
10 dB
84 dBµV
Quick start guide
5
3 dB
3 dB
F
500 mA
4 mm²
195 × 145 × 85 mm
IP 20