AIRLUX ATI32M Bedienungsanleitung Seite 23

IMPORTANT: if there is an oven under the induction hob it is
advisable for it to have a cooling fan. Do not use the induction
hob while PYROLITIC cleaning is in process.
WARNING: to allow the circulation of as much fresh air
as necessary, there must be at least 40 mm between the
induction hob module and any appliance installed under
it (fig. 10B).
In any event, adequate aeration must be provided.
To allow fresh air circulation there must be openings in the
kitchen furniture (fig. 9A-10A) of the sizes indicated in fig.
9B-10B.
ELECTRICAL CONNECTIONS (Fig.2B-3B-4B-5B)
Before making the electrical connections, check that:
- the ground cable is 2 cm longer than the other cables;
- the system ratings meet the ratings indicated on the
identification plate fixed on the lower part of the worktop;
- the system is fitted with efficient earthing compliant to the
laws and regulations in force.
Earthing is obligatory by law.
If the appliance is not fitted with a cable, use type:
"H05V2V2-F" for a power level of up to 6400 Watts. The cross-
section of the cable should be at least 2.5 mm², or 4 mm² for
greater power levels.
The cable should never reach a temperature which is 50°C
above the temperature of the room in which it is installed.
The appliance is designed for permanent connection to
the electricity supply and should therefore be fitted with
an omnipolar switch which has a minimum opening of 3
mm between contacts. The switch should be suitable for
the charge indicated on the appliance data plate and must
conform to all current legislation (the yellow/green earth wire
must not be interrupted by the switch).
The omnipolar switch must be easy to reach once the
installation process has been completed.
USE AND MAINTENANCE
A = ON/OFF button
B = - button
C = + button
D = Cooking zone selection indicators
E = Cooking zone display
OPERATION (Fig. 2-3-4-5)
- If button A is selected, the hob switches on and flashing
zeroes with decimal points will appear on all displays for
10 seconds.
If no further action is taken within this space of time, the hob
switches off again.
To switch a cooking zone on, simply select the desired power
level using the C buttons.
NOTE: each C button corresponds to a cooking zone.
0 will appear on the display, with the fixed decimal point D (no
longer flashing); at this point the zone has been selected.
If button B is used the display will show level 9, while if button
C is used, the display will show level 1.
- Once this step is complete you will be able to make
temperature adjustments using the "C" and "B" buttons.
If any object has been placed on top of the control panel, the
hob will automatically revert to OFF mode.
When a hotplate is in its OFF mode and the temperature of the
glass surface is greater than approximately 65°, a signal light
"H" will appear on the corresponding cooking zone display.
- To switch off an individual cooking zone, first select it and
then press buttons "C" and "B" simultaneously.
SAFETY LOCK FUNCTION (Fig. 3-4-5)
To prevent use the cooker surface by children, it is possible
to block all functions by pressing the S key. This function can
be activated only if the hob is switched on.
TIMER (Fig. 3-4)
A Timer can be used simultaneously for each cooking zone.
Select the desired cooking zone by pressing the corresponding
C button. Next, select the desired power level using the + and
- buttons. If the T (Timer) button is then pressed, "00" appears
on the display and the LED corresponding to the selected
zone begins to flash. Press button B; a time of 60 minutes
will be displayed. If, on the other hand, you press button T, a
time of 1 minute will be displayed. Next, set the desired time
using the T button to increase the value and the B button
to decrease it.
Once the set cooking time has elapsed, the timer switches
off and deselects the cooking zones. A buzzer will sound for
2 minutes to indicate that the timer is no longer active. To
deactivate it press any key.
To know the residual time for each zone, press the key C of the
interested zone. To set at zero the timer select the zone and
press the T key contemporaneously with the keys T and B.
Caution!
While the hob is in operation the timer display remains on,
with its value set to "00".
TIMER (fig. 5)
The Timer can be used simultaneously for each cooking
zone.
Set the desired power level.
Select the Timer by pressing the T button for the relevant
cooking zone; "00" will appear on the display and the LED
above the numbers will begin to flash. Press the B button;
a time of 30 minutes will be displayed. If, on the other hand,
you press the C button, a time of 1 minute will be displayed.
Next, set the desired time using the C button to increase the
value and the B button to decrease it.
To display the power level or view the remaining time, simply
press the T button for the relevant zone.
Once the set cooking time has elapsed, the timer switches off
and deactivates the cooking zone. A buzzer will sound for 2
minutes to indicate that the timer is no longer active. Press any
button to deactivate it. To reset the timer, press the T button
and then press the C and B buttons simultaneously.
IMPORTANT: To prevent damage being inflicted on the
electronic circuits, the hob is fitted with an overheating safety
system.In situations where the appliance is used at high
power levels for a prolonged period of time, the hob may
switchoff one or more of the activated zones temporarily,
until the temperatures return to the set levels.On the
display corresponding to the cooking zone which has been
temporarily switched off, the power level will be shown in
alternation with a H E 2.This will stop flashing once the cooking
zone has beenreactivated.
MINUTE MINDER FUNCTION (Fig. 3-4-5)
- Unblock the cooking surface by keeping the "key button" S
presseddown for 3 seconds until the "indicator light button"
is switched off.
- Press the "Timer" (T) button until the writing "00" appears
on the display.
- Press T or B to select the number of the minutes.
- Press the "Timer" button to confirm the selection.At the end
- 23 -