Werbung
in.ye-3-ce
& in.ye-5-ce
™
CO - Communication links (2 ports) in.touch, in.stik,
Aux keypad in.k112, Swim Spa com. cable, etc.
puts & keypads
2- Connect the main power
Determine jumper positions for number of phases
G
ower
ction
sories
PJ1
PJ2
N
ctions
L1
1 phase connection
Phase jumpers
Position
PJ1
P37-P49
PJ2
P50-P26
Bonding lugs
Correct wiring of the electrical service box, RCD, and pack terminal block is essential. Power must be off during this step.
Communication links (2 ports) in.touch, in.stik,
ux keypad in.k112, Swim Spa com. cable, etc.
WARNING! All connections must be made by a qualified electrician in accordance with the national electrical code and any state, provincial or local electrical code in effect
in power
at the time of the installation. This product must always be connected to circuit protected by a residual-current device (RCD).
s for number of phases
3- Select spa configuration (if prompt on startup)
version
G
1
PJ1
L2
H
L
C
G
Optional floating
connector
A0
J2
N
(Part #9920-401346)
At first startup the keypad display
will show Lx or LLx, where « x »
L1
H
L
C
G
PJ2
representing the config. number. Some
AMP ports (A0
A1
spa packs come with a pre-selected
to A5) for pumps
2 phase connection
config. and you may skip this step if
& accessories.
A2
your system automatically starts up
Functions varie per
Position
Phase jumpers
Position
configuration
PJ1
P37-P26
37-P49
A3
4- Select breaker current
(see next page).
PJ2
P50-P49
50-P26
A4 Optional connector
A4
input voltage: 230 V, 50 Hz (line-to-Neutral)
2 1
A5
cal service box, RCD, and pack terminal block is essential. Power must be off during this step.
98
ns must be made by a qualified electrician in accordance with the national electrical code and any state, provincial or local electrical code in effect
Optional board COM (RS485)
on. This product must always be connected to circuit protected by a residual-current device (RCD).
P59 A.PORT (accessories)
P62 K.PORT (keypad)
Press and hold the Program key for
guration (if prompt on startup)
20 seconds until you access the
P65 Light output
breaker setting menu.
P63 and P64 in.lu.me outputs
Note: For the Color keypad series,
2
select Settings menu, go into Electri-
cal config and choose Input current.
G
Use the Up/Down key to choose the
display
« x »
new low level configuration number.
PJ1
mber. Some
L2
elected
his step if
starts up
1
.
L3
urrent
L1
(Specify the current rating and the number of phases of the RCD used to ensure safe and efficient current mangement (and no RCD trippings).
PJ2
3 phase Delta connection
2
Position
Phase jumpers
Position
37-P38
PJ1
P37-P26
50-P49
PJ2
P50-P49
Only for countries where Line-to-Line
m key for
Current setting for each phase setting
input voltage: 230V, 50Hz.
ss the
tep.
# of phases
Current setting range
1
10 to 48 A
and any state, provincial or local electrical code in effect
d series,
ce (RCD).
2
10 to 20 A
nto Electri-
3
10 to 16 A
ut current.
Choose the number of phases
supplying your spa (1-3). Use the
Note: To re-enter the low level
1
Up/Down key to select the desired
selection menu, hold the Pump 1
value. Then press the Program key to
key for 30 seconds.
confirm the selection.
Note: For the Color keypad series,
select Settings menu, go into
confirm the
Electrical config and choose the
appropriate Low level.
our
Note: If the keypad does not have a
2
ce.com
Program or Filter key, use the Light
key instead.
fe and efficient current mangement (and no RCD trippings).
3 4
Use the Up/Down key to select the
he system
desired value. Then press the Program
um
key to confirm the selection.
e RCD.
Note: If the keypad does not have the
Program or Filter key, use the Light
key instead.
For more information, see our
website: www.geckoalliance.com
European version
™
A1
A2
A3
A4
1-Phasen-Verdrahtung (Standard)
G
A5
PJ1
L2
Für einen einphasigen Anschluss ist es notwendig, die Faston-Stecker P37-
N
P49 (PJ1) und P50-P26 (PJ2) mittels Steckbrücken zu verbinden.
L1
PJ2
L1
2 phase connection
Phase jumpers
Position
PJ1
P37-P26
Neutral
PJ2
P50-P49
input voltage: 230 V, 50 Hz (line-to-Neutral)
GND
C1 - Main keypad
connector
2-Phasen-Verdrahtung
G
2
L3
Für einen zweiphasigen Anschluss ist es notwendig, die Faston-Stecker P37-
L2
PJ1
P26 (PJ1) und P50-P49 (PJ2) mittels Steckbrücken zu verbinden.
N
Use the Up/Down key to choose the
new low level configuration number.
L1
PJ2
3 phase connection
.
1
Phase jumpers
Position
L1
PJ1
P37-P38
(Specify the current rating and the number of phases of the RCD used to ensure safe and efficient current mangement (and no RCD trippings).
PJ2
P50-P49
L2
2
Neutral
GND
Current setting for each phase setting
# of phases
Current setting range
1
10 to 48 A
3
2
10 to 20 A
3
10 to 16 A
3-Phasen-Verdrahtung
Choose the number of phases
supplying your spa (1-3). Use the
Press the Program
2
key to confirm the
Up/Down key to select the desired
selection.
value. Then press the Program key to
Für einen dreiphasigen Anschluss können die Steckbrücken von der
confirm the selection.
For more information, see our
Einspeisung vollständig getrennt werden. Die Steckbrücken können auch
website: www.geckoalliance.com
angeschlossen bleiben. In diesem Fall müssen sie an die Faston-Stecker
P37-P38 (PJ1) und P50-P49 (PJ2) angeschlossen werden.
3
L1
The values displayed by the system
correspond to the maximum
amperage capacity of the RCD.
L2
L3
Neutral
GND
5.2.2.3
Anschluss von Wellnessgeräten
Nur für Gecko YE-5; ID NUMMER 0610-221107-633 !
Zum Anschluss der Geräte können die Ausgänge A1-A5 für die originalen
Gecko AMP-Anschlüsse (falls vorhanden) verwendet werden.
Alternativ können die Geräte auch mit Flachsteckern an die Relaisklemmen
angeschlossen werden.
C1 - Main keypad
connector
H
L
C
G
Optional floating
connector
A0
G
(Part #9920-401346)
H
L
C
L3
G
AMP ports (A0
A1
L2
to A5) for pumps
PJ1
& accessories.
A2
Functions varie per
N
configuration
A3
(see next page).
L1
PJ2
A4 Optional connector
A4
braun
3 phase connection
A5
Phase jumpers
Position
PJ1
P37-P38
blau
Optional board COM (RS485)
PJ2
P50-P49
P59 A.PORT (accessories)
gelb-grün
P62 K.PORT (keypad)
P65 Light output
P63 and P64 in.lu.me outputs
G
3
PJ1
L2
L3
Press the Program
2
key to confirm the
selection.
L1
PJ2
For more information, see our
3 phase Delta connection
website: www.geckoalliance.com
Phase jumpers
Position
braun
PJ1
P37-P26
PJ2
P50-P49
schwarz
Only for countries where Line-to-Line
3
input voltage: 230V, 50Hz.
blau
gelb-grün
The values displayed by the system
correspond to the maximum
amperage capacity of the RCD.
Note: To re-enter the low level
1
selection menu, hold the Pump 1
key for 30 seconds.
Note: For the Color keypad series,
select Settings menu, go into
Electrical config and choose the
appropriate Low level.
Note: If the keypad does not have a
2
Program or Filter key, use the Light
key instead.
3 4
braun
Use the Up/Down key to select the
desired value. Then press the Program
key to confirm the selection.
schwarz
Note: If the keypad does not have the
Program or Filter key, use the Light
grau
key instead.
For more information, see our
blau
website: www.geckoalliance.com
gelb-grün
P65 Light output
P63 and P64 in.lu.me outputs
G
PJ1
L2
L3
L1
PJ2
3 phase Delta connection
Phase jumpers
Position
PJ1
P37-P26
PJ2
P50-P49
Only for countries where Line-to-Line
input voltage: 230V, 50Hz.
Note: To re-enter the low level
1
selection menu, hold the Pump 1
key for 30 seconds.
Note: For the Color keypad series,
select Settings menu, go into
Electrical config and choose the
appropriate Low level.
Note: If the keypad does not have a
2
Program or Filter key, use the Light
key instead.
3 4
Use the Up/Down key to select the
desired value. Then press the Program
key to confirm the selection.
Note: If the keypad does not have the
Program or Filter key, use the Light
key instead.
For more information, see our
website: www.geckoalliance.com
19
Werbung
