Chauvet Professional OVATIONP56VW Schnellanleitung Seite 3

FCC Compliance
This device complies with Part 15 Part B of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
What is Included
• Ovation P-56VW
• Gel frame holder (7.5 in/191 mm accessories)
®
• Neutrik powerCON
AC Power
This product has an auto-ranging power supply that can work with an input voltage range of 100–240 VAC, 50/60 Hz.
Power Linking
It is possible to link up to 7 Ovation P-56VW products at 100 VAC, 9 products at 120 V, 16 products at 208 V, 18 products
at 230 V, or 18 products at 240 VAC. Never exceed this number. Power-linking cords can be purchased separately.
AC Plug
Connection
AC Live
AC Neutral
AC Ground
To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
Replacing the Fuse
1. Disconnect this product from power.
2. Using a flathead screwdriver, unscrew the fuse holder cap from the housing.
3. Remove blown fuse and replace with a good fuse of the same type and rating.
4. Screw the fuse holder cap back in place and reconnect power.
DMX Linking
The Ovation P-56VW will work with a DMX controller using a 3- or 5-pin DMX serial connection. A DMX Primer is
available from www.chauvetprofessional.com.
DMX Connection
The Ovation P-56VW uses a 3- or 5-pin DMX data connection for its DMX personalities: 1Ch, 3Ch, 5Ch, 6Ch, 8Ch, 11Ch,
15Ch, and 18Ch. See the User Manual for information about connecting and configuring the product for DMX operation.
Master/Slave Connection
The Ovation P-56VW uses the DMX data connection for its master/slave mode. See the User Manual for information
about how to connect and configure the product for master/slave operation.
Remote Device Management
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate bi-directionally
along existing DMX cabling. Check with the manufacturer or the DMX controller's User Manual, as not all DMX controllers
have this capability. The Ovation P-56VW supports RDM protocol that allows feedback to make changes to menu map
options. Download the User Manual from
Ovation P-56VW QRG Rev. 8
QUICK REFERENCE GUIDE
®
power cord
Wire (U.S.)
Black
White
Green/Yellow
www.chauvetprofessional.com
• Medium and wide lenses
• Quick Reference Guide
Wire (Europe)
Brown
Blue
Green/Yellow
for more details.
EN
Screw Color
Yellow/Brass
Silver
Green
2